Bedienungsanleitung Makita M3601 (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691242

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

7 ENGLISH

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Router safety warnings

1. Hold power tool by insulated gripping sur-

faces, because the cutter may contact its own

cord. Cutting a “live” wire may make exposed

metal parts of the power tool “live” and shock the

operator.

2. Use clamps or another practical way to secure

and support the workpiece to a stable plat-

form. Holding the work by your hand or against

the body leaves it unstable and may lead to loss of

control.

3. Wear hearing protection during extended

period of operation.

4. Handle the router bits very carefully.

5. Check the router bit carefully for cracks or

damage before operation. Replace cracked or

damaged bit immediately.

6. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

7. Hold the tool rmly with both hands.

8. Keep hands away from rotating parts.

9. Make sure the router bit is not contacting the

workpiece before the switch is turned on.

10. Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or

wobbling that could indicate improperly

installed bit.

11. Be careful of the router bit rotating direction

and the feed direction.

12. Do not leave the tool running. Operate the tool

only when hand-held.

13. Always switch off and wait for the router bit to

come to a complete stop before removing the

tool from workpiece.

14. Do not touch the router bit immediately after

operation; it may be extremely hot and could

burn your skin.

15. Do not smear the tool base carelessly with

thinner, gasoline, oil or the like. They may

cause cracks in the tool base.

16. Use router bits of the correct shank diameter

suitable for the speed of the tool.

17. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

18. Always use the correct dust mask/respirator

for the material and application you are work-

ing with.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and unplugged before adjusting or

checking function on the tool.

Adjusting the depth of cut

1. Place the tool on a at surface. Loosen the screw

securing the stopper pole.

► Fig.1: 1. Stopper pole 2. Screw

2. Loosen the lock lever and lower the tool body until

the router bit just touches the at surface. Tighten the

lock lever to lock the tool body.

► Fig.2: 1. Lock lever 2. Screw

3. Lower the stopper pole until it makes contact with

the adjusting hex bolt. Align the depth pointer with the

"0" graduation.

► Fig.3: 1. Depth pointer 2. Screw 3. Stopper pole

4. Adjusting hex bolt 5. Stopper block

4. Raise the stopper pole until the desired depth

of cut is obtained. The depth of cut is indicated on the

scale (1 mm per graduation) by the depth pointer. Then

tighten the screw to secure the stopper pole.

5. Your predetermined depth of cut can be obtained

by loosening the lock lever and then lowering the tool

body until the stopper pole makes contact with the

adjusting hex bolt.

CAUTION: Since excessive cutting may cause

overload of the motor or difculty in controlling

the tool, the depth of cut should not be more than

15 mm (9/16″) at a pass when cutting grooves

with an 8 mm (5/16″) diameter bit.

CAUTION: When cutting grooves with a 20

mm (13/16″) diameter bit, the depth of cut should

not be more than 5 mm (3/16″) at a pass.

CAUTION: When you wish to cut grooves

more than 15 mm (9/16″) deep with an 8 mm

(5/16″) diameter bit or more than 5 mm (3/16″)

deep with a 20 mm (13/16″) diameter bit, make

several passes with progressively deeper bit

settings.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M3601 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info