Bedienungsanleitung Makita M3601 (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691242

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8 ENGLISH

Stopper block

The stopper block has three adjusting hex bolts which

raise or lower 0.8 mm (approx. 1/32″) per turn. You can

easily obtain three different depths of cut using these

adjusting hex bolts without readjusting the stopper pole.

► Fig.4: 1. Depth pointer 2. Screw 3. Stopper pole

4. Adjusting hex bolt 5. Stopper block

1. Adjust the lowest hex bolt to obtain the deepest

depth of cut, following the method of "Adjusting the

depth of cut".

2. Adjust the two remaining hex bolts to obtain shal-

lower depths of cut. The differences in height of these

hex bolts are equal to the differences in depths of cut.

3. Turn the hex bolts to adjust the depth. The stopper

block is also convenient for making three passes with

progressively deeper bit settings when cutting deep

grooves.

NOTE: When using a bit having total length of 60 mm

(2-3/8″) or more, or edge length of 35 mm (1-3/8″) or

more, the depth of cut cannot be adjusted as previ-

ously mentioned. To adjust, proceed as follows:

1. Loosen the lock lever and carefully adjust bit

protrusion below the tool base to the desired

depth of cut by moving the tool body up or

down.

2. Retighten the lock lever to lock the tool body at

that depth of cut. Keep the tool body locked at

this position during use.

Since the bit always protrudes from the tool base, be

careful when handling the tool.

Adjusting the lock lever

The locked position of the lock lever is adjustable. To

adjust it, remove the screw securing the lock lever. The

lock lever will come off. Set the lock lever at the desired

angle. After adjustment, tighten the lock lever clockwise.

► Fig.5: 1. Lock lever 2. Screw

Switch action

CAUTION: Before plugging in the tool, always

check to see that the switch trigger actuates

properly and returns to the "OFF" position when

released.

To start the tool, simply pull the switch trigger. Release

the switch trigger to stop.

► Fig.6: 1. Switch trigger

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Installing or removing the router bit

Insert the bit all the way into the collet cone and tighten

the collet nut securely with the two wrenches. An 8 mm

collet cone may be also provided as a standard equip-

ment (depending on the country) besides the 6 mm or

1/4″ collet cone that is factory installed on the tool. Use

the correct size collet cone for the bit which you intend

to use.

► Fig.7

To remove the bit, follow the installation procedure in

reverse.

CAUTION: Install the router bit securely.

Always use only the wrench provided with the

tool. A loose or overtightened router bit can be

dangerous.

CAUTION: Do not tighten the collet nut with-

out inserting a bit. It can lead to breakage of the

collet cone.

OPERATION

Set the tool base on the workpiece to be cut without

the router bit making any contact. Then turn the tool on

and wait until the router bit attains full speed. Lower the

tool body and move the tool forward over the workpiece

surface, keeping the tool base ush and advancing

smoothly until the cutting is complete.

When doing edge cutting, the workpiece surface should

be on the left side of the router bit in the feed direction.

► Fig.8: 1. Workpiece 2. Bit revolving direction

3. View from the top of the tool 4. Feed

direction

NOTE: Moving the tool forward too fast may cause

a poor quality of cut, or damage to the router bit or

motor. Moving the tool forward too slowly may burn

and mar the cut. The proper feed rate will depend on

the router bit size, the kind of workpiece and depth

of cut.

Before beginning the cut on the actual workpiece, it

is advisable to make a sample cut on a piece of scrap

lumber. This will show exactly how the cut will look as

well as enable you to check dimensions.

NOTE: When using the straight guide or the trimmer

guide, be sure to install it on the right side in the feed

direction. This will help to keep it ush with the side of

the workpiece.

► Fig.9: 1. Feed direction 2. Bit revolving direction

3. Workpiece 4. Straight guide

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M3601 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info