Bedienungsanleitung Makita M8701 (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657987

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

6 ENGLISH

►Fig.3: 1.Actionmodechangingknob

Rotation only

For drilling in wood, metal or plastic materials, rotate

the action mode changing knob to the symbol. Use a

twist drill bit or wood drill bit.

►Fig.4: 1.Actionmodechangingknob

Hammering only

For chipping, scaling or demolition operations, rotate

the action mode changing knob to the symbol. Use a

bull point, cold chisel, scaling chisel, etc.

►Fig.5: 1.Actionmodechangingknob

Torque limiter

NOTICE: As soon as the torque limiter actuates,

switch off the tool immediately.Thiswillhelppre-

vent premature wear of the tool.

NOTICE: Drill bits such as hole saw, which tend

to pinch or catch easily in the hole, are not appro-

priate for this tool.Thisisbecausetheywillcause

the torque limiter to actuate too frequently.

Thetorquelimiterwillactuatewhenacertaintorque

levelisreached.Themotorwilldisengagefromthe

output shaft. When this happens, the drill bit will stop

turning.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Side grip (auxiliary handle)

CAUTION: Always use the side grip to ensure

safe operation.

CAUTION: After installing or adjusting the

side grip, make sure that the side grip is rmly

secured.

Installthesidegripsothattheprotrusionsonthegript

inbetweenthegroovesonthetoolbarrel.Thentighten

thethumbscrewclockwisetoxthegripatthedesired

position.

Thesidegripcanbeswung360°soastobesecuredat

any position.

►Fig.6: 1. Side grip 2.Thumbscrew3.Tighten

4. Loosen

Grease

Coat the shank end of the drill bit/chisel beforehand with

a small amount of grease (about 0.5 - 1 g).

Thischucklubricationassuressmoothactionandlon-

ger service life.

Installing or removing drill bit/chisel

Clean the shank end of the drill bit/chisel and apply

grease before installing the drill bit/chisel.

►Fig.7: 1. Shank end of the drill bit/chisel 2. Grease

Insertthedrillbit/chiselintothetool.Turnthedrillbit/

chisel and push it in until it engages.

Afterinstallingthedrillbit/chisel,alwaysmakesurethat

the drill bit/chisel is securely held in place by trying to

pull it out.

►Fig.8: 1. Drill bit/chisel

Toremovethedrillbit/chisel,pullthechuckcoverdown

all the way and pull the drill bit/chisel out.

►Fig.9: 1. Drill bit/chisel 2. Chuck cover

Chisel angle (when chipping,

scaling or demolishing)

Thechiselcanbesecuredatthedesiredangle.To

change the chisel angle, rotate the action mode chang-

ingknobtotheOsymbol.Turnthechiseltothedesired

angle.

►Fig.10: 1.Actionmodechangingknob

Rotate the action mode changing knob to the

sym-

bol.Thenmakesurethatthechiselissecurelyheldin

place by turning it slightly.

Depth gauge

Thedepthgaugeisconvenientfordrillingholesof

uniformdepth.Loosenthethumbscrewandadjust

thedepthgaugetothedesireddepth.Afteradjusting,

tightenthethumbscrewrmly.

►Fig.11: 1.Thumbscrew2. Depth gauge

NOTE:Thedepthgaugecannotbeusedattheposi-

tion where the depth gauge touches against the gear

housing/motor housing.

OPERATION

CAUTION: Always use the side grip (auxiliary

handle) and rmly hold the tool by both side grip

and switch handle during operations.

CAUTION: Always make sure that the work-

piece is secured before operation.

►Fig.12

Hammer drilling operation

CAUTION:Thereistremendousandsudden

twistingforceexertedonthetool/drillbitatthetimeof

hole break-through, when the hole becomes clogged

with chips and particles, or when striking reinforcing

rods embedded in the concrete. Always use the side

grip (auxiliary handle) and rmly hold the tool by

both side grip and switch handle during opera-

tions. Failure to do so may result in the loss of control

ofthetoolandpotentiallysevereinjury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M8701 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info