Bedienungsanleitung Makita M8701 (Seite 7 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657987

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

7 ENGLISH

Set the action mode changing knob to the

symbol.

Positionthedrillbitatthedesiredlocationforthehole,

then pull the switch trigger. Do not force the tool. Light

pressure gives best results. Keep the tool in position

and prevent it from slipping away from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at

an idle, then remove the drill bit partially from the hole.

By repeating this several times, the hole will be cleaned

out and normal drilling may be resumed.

NOTE:Eccentricityinthedrillbitrotationmayoccur

whileoperatingthetoolwithnoload.Thetoolauto-

maticallycentersitselfduringoperation.Thisdoesnot

affect the drilling precision.

Chipping/Scaling/Demolition

Set the action mode changing knob to the symbol.

Holdthetoolrmlywithbothhands.Turnthetoolon

and apply slight pressure on the tool so that the tool will

not bounce around, uncontrolled.

Pressingveryhardonthetoolwillnotincreasethe

efciency.

►Fig.13

Drilling in wood or metal

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece.Thereisatremendousforceexertedon

the tool/drill bit at the time of hole break through.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

NOTICE: Never use “rotation with hammering”

when the drill chuck is installed on the tool.The

drill chuck may be damaged.

Also,thedrillchuckwillcomeoffwhenreversingthetool.

NOTICE: Pressing excessively on the tool will

not speed up the drilling.Infact,thisexcessive

pressure will only serve to damage the tip of your drill

bit, decrease the tool performance and shorten the

service life of the tool.

Set the action mode changing knob to the symbol.

Youcandrillupto13mm(1/2″)diameterinmetaland

upto32mm(1-1/4″)diameterinwood.

Use a drill chuck assembly (optional accessory). When

installing it, refer to the section “Installing or removing

drill bit/chisel”.

►Fig.14: 1. Drill chuck assembly (optional accessory)

Toinstallthedrillbit,placeitinthechuckasfarasitwill

go.Tightenthechuckbyhand.Placethechuckkeyin

each of the three holes and tighten clockwise. Be sure

to tighten all three chuck holes evenly.

Toremovethedrillbit,turnthechuckkeycounterclock-

wiseinjustonehole,thenloosenthechuckbyhand.

►Fig.15: 1. Chuck key

Diamond core drilling

NOTICE: If performing diamond core drilling

operations using “rotation with hammering”

action, the diamond core bit may be damaged.

When performing diamond core drilling operations,

always set the change lever to the position to use

"rotationonly"action.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and unplugged before attempting to

perform inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

TomaintainproductSAFETYandRELIABILITY,repairs,

carbon brush inspection and replacement, any other

maintenanceoradjustmentshouldbeperformedby

MakitaAuthorizedorFactoryServiceCenters,always

using Makita replacement parts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita M8701 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info