Bedienungsanleitung Makita UB0801 (Seite 7 von 168) (Alle Sprachen)

690556

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

• Waste electrical products should

not be disposed of with household

waste. Please recycle where

facilities exist. Check with your local

authority or retailer for recycling

advice.

• Double insulation

SAFETY WARNINGS

1. Important safety instruction

• Please read all of the safety and operating instructions

carefully before using this product. Please pay particular

attention to all sections of this operator manual that

carry warning symbols and notices. Failure to follow the

warnings and instructions may result in electric shock,

burn, and/or serious injury.

• This tool is intended for blowing and mulching. Never

use the tool other than its intended use, such as inat-

ing balloons.

• The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and

can only be operated on single-phase AC supply. They

are double-insulated and can, therefore, also be used

from sockets without earth wire.

• Save all warning and instructions for future reference.

2. Training

• Read the instructions carefully. Be familiar with the

controls and the proper use of the tool.

• Never allow children, persons with reduced physical,

sensory or mental capabilities or lack of experience and

knowledge or people unfamiliar with these instructions

to use the blower. Local regulations may restrict the age

of the operator.

• Never operate the tool while people, especially children,

or pets are nearby.

• The operator or user is responsible for accidents or

hazards occurring to other people or their property.

3. Preparation

• While operating the tool, always wear substantial

footwear and long trousers.

• Dress properly - Do not wear loose clothing or jewel-

lery. They can be caught in moving parts. Use of sturdy

gloves and substantial footwear is recommended when

working outdoors.

• Wear protective hair covering to contain long hair. Wear

protective goggles while operating.

• To prevent dust irritation the wearing of a face mask is

recommended.

• Before using, check the supply and extension cord for

signs of damage and aging. Do not use the tool if the

cord is damaged or worn.

• Never operate the tool with defective guards or shields,

or without safety devices, for example collection bag in

place.

• Only use a weather proof extension cable correctly

rated to your machine.

4. Operation

• Always direct the cable to the rear away from the tool.

• If the cord becomes damaged during use, disconnect

the cord from the supply immediately. DO NOT TOUCH

THE CORD BEFORE DISCONNECTING FROM THE

SUPPLY. Do not use the tool if the cord is damaged

or worn.

• Do not carry the tool by the cable.

• Avoid Dangerous Environment - Don’t use the tool in

damp or wet locations.

• Disconnect the tool from the mains supply:

– whenever you leave the tool.

– before clearing a blockage.

– before checking, cleaning or working on the tool.

• Switch off the tool immediately, disconnect the tool

from the mains supply and inspect for obstructions or

damage to the unit:

– after striking a foreign object.

– if the tool starts to vibrate abnormally.

• Operate the tool only in daylight or in good articial light.

• Do not overreach and keep your balance at all times.

• Always be sure of your footing on slopes.

• Walk, never run.

• Keep all cooling air inlets clear of debris.

• Never blow debris in the direction of bystanders.

• The tool should be supplied via a residual device with a

tripping current of not more than 30 mA.

5. Maintenance and storage

• Before servicing, inspection, or storage, or to change an

accessory, switch off the tool, remove the plug from the

mains and wait until all moving parts stop completely.

Cool down the tool before making any inspections,

adjustments, etc. Maintain the blower with care and

keep it clean.

• Keep all nuts, bolts and screw tight to be sure the tool is

in safe working condition.

• Check the tool frequently for wear or deterioration.

• Replace worn or damaged parts.

• Use only genuine replacement parts and accessories.

• Store Idle Tools Indoors - When not in use, tools should

be stored indoors in dry, and high or locked-up place

- out of reach of children.

6. Additional safety rules for blower / mulcher

• Always wear adequate protective clothing when

operating the tool to avoid injuries to face, eyes, hands,

feet, head or hearing. Use safety glasses or a face

shield, high boots or sturdy shoes, long trousers, work

gloves, a hard hat and ear defenders.

• Do not start the tool when it is upside down or when it is

not in the operating position.

• Switch the motor off and disconnect from power when

the tool is not being used, left unattended, being

cleaned, being moved from one place to another or

when the extension cord is entangled or damaged.

• Do not operate the tool near people, especially children

or pets. Turn it off if they get too close. Maintain a safe

distance of at least 5 m from other people when using

the tool.

• Never direct the blower tube towards bystanders or

pets. Never blow debris in the direction of bystanders

or pets. The operator is responsible for accidents or

hazards occurring to other people or their property.

• Do not handle the plug or the tool with wet hands and

do not use the tool in the rain.

Makita UB0801 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info