Bedienungsanleitung Makita UR100D (Seite 10 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690918

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

10 ENGLISH

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Electrical and battery safety

Avoid dangerous environment. Don't use the tool in

damp or wet locations or expose it to rain. Water enter-

ing the tool will increase the risk of electric shock.

2. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of

re when used with another battery pack.

3. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

4. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a re.

Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ush with water. If liquid

contacts eyes, seek medical help. Liquid ejected

from the battery may cause irritation or burns.

6. Do not dispose of the battery(ies) in a re. The

cell may explode. Check with local codes for

possible special disposal instructions.

Do not open or mutilate the battery(ies). Released

electrolyte is corrosive and may cause damage to

the eyes or skin. It may be toxic if swallowed.

Starting up the tool

►Fig.3

1. Make sure that there are no children or other

people within a working range of 15 meters

(50 ft), also pay attention to any animals in the

working vicinity. Otherwise stop using the tool.

Before use always check that the tool is safe for

operation. Check the security of the cutting tool

and the guard and the switch trigger/lever for

easy and proper action. Check for clean and dry

handles and test the on/off function of the switch.

3. Check damaged parts before further use of

the tool. A guard or other part that is damaged

should be carefully checked to determine

that it will operate properly and perform

its intended function. Check for alignment

of moving parts, binding of moving parts,

breakage of parts, mounting, and any other

condition that may affect its operation. A guard

or other part that is damaged should be prop-

erly repaired or replaced by our authorized

service center unless indicated elsewhere in

this manual.

4. Switch on the motor only when hands and feet

are away from the cutting tool.

5. Before starting make sure that the cutting

tool has no contact with hard objects such as

branches, stones etc. as the cutting tool will

revolve when starting.

6. Make sure there are no electrical cables, water

pipes, gas pipes etc. that could cause a hazard

if damaged by use of the tool.

Method of operation

1. Never operate the machine with damaged

guards or without the guards in place.

2. Only use the tool in good light and visibility.

During the winter season beware of slippery

or wet areas, ice and snow (risk of slipping).

Always ensure a safe footing.

3. Take care against injury to feet and hands from

the cutting tool.

4. Keep hands and feet away from the cutting

means at all times and especially when switch-

ing on the motor.

5. Never cut above waist height.

6. Never stand on a ladder and run the tool.

7. Never work on unstable surfaces.

8. Don't overreach. Keep proper footing and

balance at all times.

9. Remove sand, stones, nails etc. found within

the working range. Foreign particles may

damage the cutting tool and can cause to be

thrown away, resulting in a serious injury.

10. Should the cutting tool hit stones or other hard

objects, immediately switch off the motor and

inspect the cutting tool.

11. Before commencing cutting, the cutting tool

must have reached full working speed.

12. During operation always hold the tool with

both hands. Never hold the tool with one hand

during use. Always ensure a safe footing.

13. All protective equipment such as guards

supplied with the tool must be used during

operation.

14. Except in case of emergency, never drop

or cast the tool to the ground or this may

severely damage the tool.

15. Never drag the tool on the ground when mov-

ing from place to place, the tool may become

damaged if moved in this manner.

16. Always remove the battery cartridge from the

tool:

— whenever leaving the tool unattended;

— before clearing a blockage;

— before checking, cleaning or working on

the tool;

— before making any adjustments, chang-

ing accessories or storing;

— whenever the tool starts vibrating

unusually;

— whenever transporting the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita UR100D Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info