Bedienungsanleitung Makita VC2510L (Seite 11 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598792

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

4. Resting a reasonable size of electric power tool

for the base hook, such as circular saw. (Fig. 8)

Locking or unlocking the caster

For Models VC1310L and VC2510L (Fig. 9)

For Model VC3210L (Fig. 10)

To lock the caster with a stopper, lower the stopper lever

and the caster no longer will rotate. To release the caster

from the locked position, raise the stopper lever.

Locking the caster is convenient when storing the cleaner,

stopping the work on the way and keeping the cleaner

still.

To operate the stopper, move it by hand.

NOTE:

• When moving the cleaner, make sure that the caster is

unlocked. Moving the cleaner with the caster in the

locked position may cause damage to the caster.

ASSEMBLY

CAUTION:

• Always be sure that the cleaner is switched off and

unplugged before carrying out any work on the cleaner.

Installing the water filter (Fig. 11)

To pick up water or wet dust, remove prefilter and damper

and then use water filter.

When installing the water filter on the tank, set it tight at

the opening of the tank so that the hook of the water filter

engages the tank opening firmly and there is no space

between the water filter and the tank. (Fig. 12)

Also, install the water filter so that the mounting position

marking can be aligned.

NOTE:

• Models VC2510L and VC3210L have no mounting

position marking and no need to align it.

Installing the paper pack

WARNING:

• When using the paper pack, also use the prefilter

together that is preinstalled on the tool. Failure to use

the prefilter together may cause unusual noise and

heat, resulting in a fire.

CAUTION:

• Never pick up water or other liquids or wet dusts when

using the paper pack. Picking up such things may

cause the paper pack breakage.

1. Remove the rubber holder. (Fig. 13)

2. Extend the paper pack.

3. Align the paper pack opening with the dust suction

opening of the cleaner. (Fig. 14 & 15)

4. Insert the cardboard of the paper pack onto the too so

that it is positioned at the end beyond the detent

protrusion.

Installing the pipe holder (optional

accessory)

For Model VC1310L only

Depress the cord hook as shown in the figure. (Fig. 16)

Attach the pipe holder onto the cord hook. (The hooks are

away from the tank cover.)

Raise the pipe holder as far as the hooks contact the tank

cover and press the A section of the pipe holder. (Fig. 17)

Press the A section with a great force and with the A

section so pressed lower the pipe holder. (Fig. 18)

Fit two protrusion of the pipe holder into the grooves of the

tank cover and then press down the pipe holder. (Fig. 19

& 20)

NOTE:

• The pipe holder that is excessively lowered than the

intended position cannot be installed on the cord hook

with the hook away from the tank cover as shown in the

figure. (Fig. 21)

NOTE:

• Make sure that the two hooks of the pipe holder are

hooked on the tank cover securely. (Fig. 22)

Connecting a hose

CAUTION:

• Never force the hose for bending or stamp it. Never

move the cleaner by a hose. Forcing, stamping and

pulling the hose may cause a breakage or deformation

of the hose.

• When picking up large wastes such as planer carvings,

concrete dusts or similars other than small wastes, use

the 38 mm inner diameter hose (optional accessory).

Using the 28 mm inner diameter hose may cause a

hose stuffing and damage.

Insert the hose onto the mounting port of the tank and turn

it clockwise until it locks. (Fig. 23)

Installing polyethylene bag

Cleaner can also be used without polyethylene bag.

However, using polyethylene bag is easier to empty the

tank without letting your hands dirty.

Spread the polyethylene bag in the tank. Insert it between

the holder plate and the tank, and pull it to the hose inlet.

(Fig. 24)

Spread the bag around the top of the tank.

Hook up the other side of the bag around the top of the

tank so that the prefilter hook can catch and hold it

securely. (Fig. 25)

NOTE:

• A polyethylene bag available on the market can be

used. The 0.04 mm or thicker one is recommended.

• Too much dust will tear the bag easily, so do not collect

the dust more than the half of the bag capacity.

Emptying the polyethylene bag

WARNING:

• Always make sure that the cleaner is switched off and

unplugged before emptying the polyethylene bag.

Failure to do so may cause an electric shock and

serious personal injury.

CAUTION:

• Do not apply a great impact on the powder filter and

tank. Applying a great impact may cause deformation

and damage to powder filter and tank.

• Empty the tank at least once a day although this

depends on picked-up dust volume in the tank. Or, the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita VC2510L Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info