Bedienungsanleitung Mamiya 645 AFD III (Seite 45 von 56) (Englisch)

494220

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

87 88

1. The selected shutter speed and aperture level can be locked.

See page 79

2. The sync. speed can be set between 1/40 and 1/125 seconds.

Custom settings (C-23 on page 95)

* When the shutter speed is set to 1/2 increments, the sync. speed can be set between 1/45 and 1/125

seconds.

Flash Photography with electronic flash models other

than Metz

1. To use a grip type flashgun or a strobe with

other electric contacts than X contact, connect

the sync. cord to the camera’s sync. terminal.

(See note below about flashes designed exclu-

sively for other maker’s cameras.)

2. While pressing the unlock button, turn the exposure mode setting dial and set it to “X”

(1/125 sec.) or “M” (manual).

When “M” (manual) is selected, turn the front dial and set the shutter speed to 1/125 sec.

or slower.

3. Turn the rear dial to set the aperture, then take the picture.

★ This camera’s synchro contact is an X contact.

★ Remove the rubber cover when connecting the sync. cord.

After shooting, be sure to attach the rubber cover in order to protect the synchro

terminal’s contacts.

WARNING

- Using flashes designed exclusively for other maker’s cameras may

damage the camera’s internal mechanisms if connected to the camera's

hot-shoe. In this situation, use an off-camera flash bracket and connect

a sync. cord to the camera's synchro terminal.

- When using flashes with a flash duration of 1/500 sec. or longer, set the

shutter speed to 1/30 sec. or less.

Superimposing Data

This is a function to allow various pieces of shoot-

ing information to be superimposed on the edge

of the film. The info that is superimposed can be

selected from the following three modes. To specify

this function, use the Custom settings (C-02 on

page 93).

This section describes the details of the informa-

tion that can be superimposed.

INDEX mode

(Superimpose only an index number)

①

②

③

④

⑤

⑥

⑦

DATA/INDEX mode

(Superimpose shooting info and an index number)

①

②

③

④

⑤

⑥

⑦

⑧

When manual exposure is selected and when the exposure metering

difference exceeds ±6EV, "– o –" or "– u –" will be superimposed on

⑤

Data superimposed in manual mode

DATE/INDEX mode

(Superimpose the date and an index number)

① ② ③

＊

75 64321

321

86 754321

* When the metering mode is selected as AUTO A-S (automatic change between average and spot), and if “A” is

selected, “A” will be superimposed. If “S” is selected, “S” will be superimposed. If “AUTO A-S” is selected, “As” will be

superimposed.

★ The data superimpose function is available with films having sensitivity from ISO25

to 1600. When using other films, even if the data superimpose function is used, data

will not be superimposed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mamiya 645 AFD III Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info