Bedienungsanleitung Marantec Comfort RA2224E (Seite 5 von 52) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

742798

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

4 - PRODUCT INSTALLATION

4.1 - Installation

4.2 - Installing the rear xing bracket with inward opening

4.3 - Installing the front xing bracket with inward opening

The xing position of the rear bracket is determined according to the

graph (Fig. 4).

Important: installations where the values of “A” and “B” (Fig. 4) are

as similar to each other as possible are preferred (l.o.= optimal line).

Identify dimension C found and trace a horizontal line that

determines the value of dimension B (*) as shown in the example

of g. 4b; the meeting point with line “l.o.” (optimal line) determines

the value of the angle of maximum opening; from this point, trace a

vertical line as shown in the example of g. 4b to determine the value

The front bracket must be xed to the door according to dimension

“E” of Table 1 (Fig.5).

Note: If you mount the closing limit switch, reduce the value “E” of

of dimension A.

If the angle found does not correspond to the requirements, adapt

dimension A and if necessary dimension B, so they are similar.

(*) Do not use values of dimension B below the line “l.s.”

If necessary, cut the rear bracket (Fig. 7) to obtain the value “B”, then

weld the xing bracket to the wall.

Secure the bracket to the wall using welding, screws or bolts (not

included).

40 mm.

The front bracket must be xed as the same height as the rear

bracket (Fig.8).

Before proceeding with the installation, check the integrity of the

product and that all components are present in the package (Fig. 3).

Also make sure that the mounting area of the gear motor is

Also check that the gearmotor’s installation zone is compatible with

its overall dimensions (Fig.1).

Check the opening angle permitted by the bracket xing points using

the graph in Fig.4 for inward opening. For outward opening, refer to

the graph in Fig.4.1.

Fig.6 shows a typical installation:

Gear motors (1)

Photocells (2)

Columns for photocells (3)

Flashing light with antenna (4)

Key switch or digital keypad (5)

Control unit (6)

Pressure-sensitive edge (7)

The automation system must be equipped with a pressure-sen-

sitive edge protecting all possible crushing points (hands, feet,

etc.) in accordance with the requirements of the EN 13241-1

standard.

The gate must have limit stops in the open and closed posi-

tions which prevent it from travelling over the permitted limits.

The installer must verify that the working temperature range

stated on the automation device is suitable for the location

where it is installed.

ATTENTION !

4.5 - Installing the front xing bracket with outward opening

4.4 - Installing the rear xing bracket with outward opening

The EXRB accessory is required for outward opening. Measure di-

stance “C1”. If distance “C1” is 130 mm or less, refer to Fig. 5.1A; if

it is more than 130 mm, refer to Fig 5.1B.

To establish distance “B1” draw a horizontal line from the value of

distance “C1” (Fig.4.1); the point where the areas of the graph meet

provides the possible values of point “A1”.

After fastening the rear xing bracket to the wall, screw on the optio-

nal brackets EXRB as shown in Fig. 5.1A or Fig. 5.1B.

The front bracket must be xed to the leaf in accordance with distan-

ces “E1” (Tab.2, Fig.5.1) and must be xed at the same height as

the rear bracket (Fig.8).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantec Comfort RA2224E Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info