Bedienungsanleitung Marantec Comfort RA2224E (Seite 6 von 52) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

742798

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

If you need to also adjust the mechanical limit switch in closing

(optional FCRAY), repeat the same procedure, this time manually

bringing the door to the point of closure you want.

N.B. The working travel stroke is reduced by 40 mm for every limit

switch installed.

Release the gear motor (Fig.11).

Loosen the screw on the mechanical limit switch until it is able to

slide.

Open the door manually to the point of desired opening.

Bring the mechanical limit switch up to pin of the slide bracket and

secure it with the screw (Fig.12).

4.8 - Setting of the mechanical limit switch while opening

4.7 - Electrical connections

Loosen the cable gland and insert the power cord (Fig.13).

connect the wires of the power cable to the terminal block

according to the wiring diagram (Fig.14/14a).

Screw the cable gland.

4.6 - Installing the gear motor

Open the release door and remove the 2 screws that secure the rear

cover (Fig. 9A).

Remove the top cover rst sliding it slightly backward (Fig. 9A)

Place the gear motor against the rear bracket and insert the xing

screw (Fig.9B).

5.2 Commissioning

Following the successful testing of all (and not just some) devices in

the system you can proceed with the commissioning.

You must prepare, and keep for 10 years, the technical le of the

system with the wiring diagram, drawing or photo of the system,

risks analysis and solutions adopted, manufacturer declaration of

conformity of all devices connected, instruction manual of each de-

vice and maintenance schedule of the system.

Fix on the gate or door a plaque indicating the automation data, the

name of the person responsible for the commissioning, the serial

number and year of construction, the CE mark.

Attach a plaque indicating the steps required to manually unlock

the system.

Implement and deliver to the end user the declaration of conform-

ity, the instructions and warnings for use for the end user and the

maintenance schedule of the system.

Make sure the user understands proper automatic, manual and

emergency operation of the automation.

Inform the end user in writing of the dangers and risks still present.

5.1 Testing

All system components must be tested following the procedures

outlined in the respective instruction manuals.

Check that they meet the guidelines in Chapter 1 - Safety warnings

Check that the gate or door can move freely once the automation

is unlocked, and that they are in equilibrium and stationary if left in

any position.

Check the correct operation of all connected devices (photocells,

sensitive edges, emergency buttons, etc.), testing the opening,

closing and stopping of the gate or door via the connected control

devices (transmitters, buttons, switches).

Carry out measurements of the impact force, as prescribed by

standard EN12453 adjusting the functions of speed, motor force

and deceleration of the unit if the measurements do not give the

desired results until you nd the right setting.

The testing of the system must be performed by qualied techni-

cians who must perform the tests required by relevant legislation

related to risks, ensuring compliance with the provisions of the

regulations, in particular the EN12453 standard, which species the

testing methods for the automation of doors and gates.

5- TESTING AND COMMISSIONING THE AUTOMATION

Replace the top cover, rst sliding it slightly forward.

Open the door and tighten the 2 screws that secure the rear cover.

Insert the pin of the sliding bracket into the bush of the front bracket

and secure it with the screw and washer provided (Fig.9C).

Tighten without applying too much force, using the nut and washer

of the screw of the rear bracket tted earlier (Fig.9D).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantec Comfort RA2224E Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info