Bedienungsanleitung Marantec Comfort SU500F (Seite 3 von 52) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

742805

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

1 - SAFETY WARNINGS

ORIGINAL INSTRUCTIONS - important safety instructions. Fol-

low the instructions since incorrect installation can lead to se-

vere inquiry! Save these instructions.

Read the instructions carefully before proceeding with installation.

The design and manufacture of the devices making up the

product and the information in this manual are compliant with

current safety standards. However, incorrect installation or

programming may cause serious injury to those working on or

using the system. Compliance with the instructions provided

here when installing the product is therefore extremely impor-

tant.

If in any doubt regarding installation, do not proceed and contact the

Marantec Technical Service for clarications.

Under European legislation, an automatic door or gate system

must comply with the standards envisaged in the Directive

2006/42/EC (Machinery Directive) and in particular standards

EN 12453; EN 12635 and EN 13241-1, which enable declaration

of presumed conformity of the automation system.

Therefore, nal connection of the automation system to the electri-

cal mains, system testing, commissioning and routine maintenance

must be performed by skilled, qualied personnel, in observance of

the instructions in the “Testing and commissioning the automation

system” section.

The aforesaid personnel are also responsible for the tests required

to verify the solutions adopted according to the risks present, and for

ensuring observance of all legal provisions, standards and regula-

tions, with particular reference to all requirements of the EN12453

standard which establishes the test methods for testing door and

gate automation systems.

Before starting installation, perform the following checks and

assessments:

ensure that every device used to set up the automation system is

suited to the intended system overall. For this purpose, pay special

attention to the data provided in the “Technical specications” sec-

tion. Do not proceed with installation if any one of these devices is

not suitable for its intended purpose;

check that the devices purchased are su󰀩cient to guarantee system

safety and functionality;

perform a risk assessment, including a list of the essential safety

requirements as envisaged in Annex I of the Machinery Directive,

specifying the solutions adopted. The risk assessment is one of the

documents included in the automation system’s technical le. This

must be compiled by a professional installer.

Considering the risk situations that may arise during instal-

lation phases and use of the product, the automation system

must be installed in compliance with the following safety pre-

cautions:

never make modications to any part of the automation system other

than those specied in this manual. Operations of this type can only

lead to malfunctions. The manufacturer declines all liability for da-

mage caused by unauthorised modications to products;

if the power cable is damaged, it must be replaced by the manufac-

turer or its after-sales service, or in all cases by a person with similar

qualications, to prevent all risks;

do not allow parts of the automation system to be immersed in water

or other liquids. During installation ensure that no liquids are able to

enter the various devices;

should this occur, disconnect the power supply immediately and

contact a Marantec Service Centre. Use of the automation system in

these conditions may cause hazards;

never place automation system components near to sources of heat

or expose them to naked lights. This may damage system compo-

nents and cause malfunctions, re or hazards;

The drive shall be disconnected from its power source during

cleaning, maintenance and when replacing parts. If the discon-

nect device is not in a visible location, a󰀩x a notice stating:

“MAINTENANCE IN PROGRESS”:

connect all devices to an electric power line equipped with an

earthing system;

the product cannot be considered to provide e󰀨ective protection

against intrusion. If e󰀨ective protection is required, the automation

system must be combined with other devices;

the product may not be used until the automation system “commis-

sioning” procedure has been performed as specied in the “Automa-

tion system testing and commissioning” section;

the system power supply line must include a circuit breaker device

with a contact gap allowing complete disconnection in the conditions

specied by class III overvoltage;

use unions with IP55 or higher protection when connecting hoses,

pipes or cable glands;

the electrical system upstream of the automation system must com-

ply with the relevant regulations and be constructed to good wor-

kmanship standards;

this appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervi-

sion or instruction concerning use of the appliance in a safe way and

understand the hazards involved;

before starting the automation system, ensure that there is no-one

in the immediate vicinity;

before proceeding with any cleaning or maintenance work on the

automation system, disconnect it from the electrical mains;

special care must be taken to avoid crushing between the part ope-

rated by the automation system and any xed parts around it;

children must be supervised to ensure that they do not play with the

equipment.

that the drive cannot be used with a driven part incorporating a wi-

cket door unless the drive can only be operated with the wicket door

in the safe position;

The automation system component packaging material must

be disposed of in full observance of current local waste dispo-

sal legislation.

Marantec reserves the right to amend these instructions if ne-

cessary; they and/or any more recent versions are available at

www.marantec.com

Frequently examine the installation for imbalance where ap-

plicable and signs of wear or damage to cables, springs and

mounting.

Do not use if repair or adjustment is necessary.

ATTENTION !

Marantec Comfort SU500F Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info