Bedienungsanleitung Marantz SR-18EX (Seite 35 von 47) (Englisch)

6546

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

ENGLISH

To “clone” (duplicate) the memory contents of one RC-18SR

into another RC-18SR or RC2000MKII, please follow these steps:

1. Place the source RC-18SR (the one with all of the customized

commands, names, macros, macro sequences, etc) with its

infrared transmitter window ¤1 facing the receiving infrared

sensor ¤2 of another “fresh” RC-18SR or RC2000MKII (5 cm, or 2

inches apart).

2. Press the CLONE button c of the source RC-18SR or

RC2000MKII with the tip of a paper clip, and select “CLONE TX”

(clone transmit) mode .

Note:

When using RC18SR, “RC2002” is displayed in LCD window. If

the receiving remote control unit is RC2000MKII , then the display

does not change. If the receiving remote control unit is RC-18SR,

then the display is changed to “RC18SR” by pressing the cursor

button ⁄6. (see Figure 20)

Figure 20

3. Press the CLONE button c of the learning (receiving) RC-18SR or

RC2000MKII with the tip of a paper clip or a similar object, and

select “CLONE RX” (clone receive mode).

When using RC18SR, “RC2002” is displayed in LCD window. If

the transmitting remote control unit is RC2000MKII , then the

display does not change. If the transmitting remote control unit is

RC-18SR, then the display is changed to “RC18SR” by pressing

the cursor button ⁄6. Then press the PLAY button ⁄5.

Note:

When the transmitting remote control unit is RC2000MKII , then

All clone does not activate. To clone the Function key, press the

each Function key except DSS/VCR2 and AMP keys. Eight keys

can be cloned at once. If All clone activates without pressing the

Function button, “N/A” will display and the clone is not perfomed

When the transmitting remote control unit is RC-18SR and

receiving remote control unit is RC2000MKII, The DSS/VCR2,

CD-R/MD and AMP keys cannot be cloned. To clone the

Function key, press each Function key except DSS/VCR2, CD-R/

MD and AMP keys.

Figure 21

4. Press the source RC-18SR’s or RC2000MKII’s transport control

PLAY ⁄5 button to begin the infrared data transmission

sequence. If you wish to duplicate only 1 to 8 function’s memory,

press the function button(s) you wish before pressing the PLAY

button. Now the “LEARN” indicator of receiving RC-18SR starts

to blink. (see Figure 23)

Figure 22 Figure 23

After all bars are lit up on both displays, “TX OK” (transmission OK)

will appear in the source RC-18SR’s LCD window, and “RX OK”

(reception OK) will appear in the “cloned” RC-18SR’s LCD window,

confirming the end of the copying process (see Figures 24 and 25).

Figure 24 Figure 25

Please be sure that, during the copying process, neither RC-18SR is

physically disturbed (ideally, they should be placed on a table or

other surface, and not hand-held during the copying process). If, for

some reason, the copying process was interrupted, the “clone” RC-

18SR’s LCD display window will indicate “RX NG” (reception no

good). Simply begin the clone process anew by repeating the above

steps.

Note:

Cloning is only available between the same remote control unit series,

therefore the RC-18SR cannot be cloned by the RC2000.

5. If the source RC-18SR’s memory contents are at or near full

capacity, the copying process will take about 3 minutes. After

completion of the copying (cloning) process, press the CLONE

button c on both RC-18SR’s with the tip of a paper clip, and

select the OFF mode.

Then, you’ll have two identically programmed RC-18SR remotes,

one of which can again be used as your system’s primary remote

control, and you’ll have the added confidence of knowing that in

the event of inadvertent programming (or memory contents being

cleared somehow), you can simply retrieve the “backup” RC-

18SR that you’ve safely tucked away, and within minutes restore

the programming contents of the original RC-18SR with your

customized configuration.

Note:

Some direct keys are marked “♦” in Direct Command Functions

Listing (page 32 to 35). The “♦” mark means as follows;

When RC-18SR is cloned with RC2000MKII, the name of the direct

key can be cloned, however the remote control code (the factory

preset code) cannot be cloned. Only learned remote control codes

can be cloned. Then the remote control code is learned by “LEARN

mode”. Refer to page 25.

The table of cloning relations

ALL OK: All functions can be cloned.

only FUNC.: The following functions cannot be cloned;

RC-18SR: DSS/VCR2, CD-R/MD, AMP

RC2000MKII: DSS/MD, AMP

LEARN

Transmitting

Receiving

RC-18SR

RC2000MKII

RC-18SR

ALL OK

only FUNC.

RC2000MKII

only FUNC.

ALL OK

LOW

NAME

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR-18EX Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info