Bedienungsanleitung Marantz SR-9300 (Seite 8 von 14) (Englisch)

6612

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

ENGLISH

SPEAKERS LEVEL

Here you will set the volume for each speaker so that they are all

heard by the listener at the same level.

Note:

• The speaker level settings is not available in 7.1channel input

mode and S-Direct mode.

TEST MODE : Selects “MANUAL” or “AUTO” for generating mode of

test tone Left or Right cursor button.

If you select “AUTO” , the test tone will be cycled through in a circular

pattern which is Left →Center →Right →Surround Right →Surround

Back Right →Surround Back Left →Surround Left →Subwoofer

→Left →.. increments of 3 seconds for each channel.

Using the Left and Right cursor buttons, adjust the volume level of the

noise from the speaker so that it is the same level for all speaker.

If you select “MANUAL”, adjust the output level of each speaker as

follow.

When you move cursor to FRONT L by pressing Down cursor

button, the SR9300 will emit a pink noise from the front left

speaker.

At this time, the master volume automatically increases to the

reference level (0dB).

Remember the level of this noise and then press the Down cursor

button.

(Note that this can be adjusted to any level between -10 and +10

dB in 1db intervals.)

The SR9300 will now emit the pink noise from the center speaker.

Using the Left and Right cursor buttons, adjust the volume level

of the noise from the center speaker so that it is the same level as

the front left speaker.

Press the Down cursor button again. The SR9300 will now emit

the pink noise from the front right speaker.

Repeat steps 2 and 3 above for the front right and other speakers

until all speakers are adjusted to the same volume level.

If you finish these setup, press OK button, the cursor will move to

“NEXT” and then press OK button to go to next page.

Notes:

• Speakers that you selected “No” or “None” for in the Speaker

Size menu will not appear.

• The setting of Surr.Back L and Surr.Back R appears if set for

two surround back speakers in the Speaker Size menu.

• The setting of Surr.Back appears if set for one surround back

speaker in the Speaker Size menu.

• The setup level for each channel is memorized for reproduction

in all surround mode.

• To adjust the speaker levels for 7.1-channel input sources, you

will need to use the 7.1CH-INPUT sub menu. (See page 36).

• In order to correctly set the output levels, use a hand-held Sound

Pressure Level meter (SPL), set to C-Weighting and Slow

averaging. A Radio Shack

SPL meter (catalogue number 330

- 2055) works well. Using the internal channel noise

generators, set each channel so that you read 75 dB SPL from

each channel when seated at the listening position.

2 - 5 BASS PEAK LEVEL

BASS PEAK TEST : START

VOLUME LEVEL : +18dB

--------------------

ENTER

MA I N R E TURN EX I T

2-4 SPEAKERS LEVEL

T EST MODE : MANUAL

FRONT L : 0 dB

CENTER : 0 dB

FRONT R : 0 dB

SURR . R : 0 dB

SURR . B R : 0 dB

SURR . B L : 0 dB

SURR . L : 0 dB

SUB W : 0 dB

MA I N RETURN NEXT EX I T

BASS PEAK LEVEL

With Dolby Digital and DTS , not only the LFE (Low Frequency

Effects), but also the bass of all channels can be heard from the

Subwoofer or Large-speakers. This procedure prevents these

speakers from becoming too loud and creating an unbalanced sound.

Since the sound is output at a loud volume, perform this operation

carefully.

Note:

• If your system does not include a subwoofer, this setting will set

the bass peak level for your front speakers.

TEST SIGNAL: Press the OK or Left button, START is indicated and

it begins to generate a Bass test tone from the

speaker which was designated “bass signal output”

during setup.

There will be no audible sound yet because the

Master volume is set to minimum automatically.

Press Down cursor button to move the cursor to

VOLUME control.

VOLUME: Adjust the bass test tone output level up until the

bass begins to distort or you reach the maximum

level with the VOL+, VOL– or Right / Left cursor

button.

Press Down cursor button to move the cursor to

ENTER.

ENTER: Press the OK button, ENTER will blink and stop

generating the Bass Peak test tone.

The Bass Peak Limit Level for your system has now

been memorized.

If you finish these setup, move cursor to “MAIN” with Up or Down

cursor button and then press OK button to go to MAIN menu.

Notes:

• Each time the subwoofer level is changed, perform the Bass

Peak Level setup and correct the setting.

• The bass peak level is not available in SOURCE-DIRECT and

7.1CH-INPUT mode.

• The selected value is displayed in the volume column before the

test signal starts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR-9300 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR-9300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info