522824

Marantz SR14 MKII Seite 22

22
Zoom out
Zoom in
Vorherige Seite
1/35
Nächste Seite
ENGLISH
15
SPKRS SETUP 2/2 (SPEAKER DISTANCE)
Speaker distance for time alignment
Use this parameter to specify the distance of each speaker’s position
from the listening position. The delay time is automatically calculated
according to these distances.
UNITS: The units may be selected in “ft” or “m” with < or > button.
If you select “ft” the setting parameter will change in 1 foot
increments. If you select “m” it will change in 0.3 meters
increments.
Begin by determining the ideal or most commonly used seating
position in the room.
(There are several usefull books and special DVD and LD’s available
to guide you through proper home theater configuration. If you are
unsure, have your Marantz dealer perform the installation for you.
They are trained professionals familiar with even the most
sophisticated custom installations. Marantz recommends the
WWW.CEDIA.ORG website for further information about this).
Then provide the distance values from that point to each speaker
during the speaker setup process.
Select the target speaker with “ok” button, and input parameter with
< or > button.
After input for each speaker’s distance has been finished ,move
cursor to ENTER with ^ or v button and press the ok button.
If your input is out of the range of the SR-14mkII’s processing,
“incomplete channel” will flash.
In that case, input an acceptable parameter or improve the speaker
placement.
The maximum distance a speaker may be placed is 30 feet (9 meters)
from the listening position, which means you can setup your system in
a room which is 60 feet long! If your home theater room is larger than
this please consult a professional as it is sized more closely to a real
movie theater!
The time aligment feature does not function in the STEREO, SOURCE-
DIRECT, 5ch Stereo and 6 CHANNEL INPUT modes.
RETURN : If you desire to return the main menu , press the “ok“
button on RETURN .
EXIT : If you desire to exit from OSD menu system, press the
“ok” button on EXIT.
LEVELS SETUP 1/2 (TEST TONE GENERATOR)
TEST MODE : Selects the mode for generating the test tone. If you
select AUTO with < or > button, the test tone will be
cycled through in a circular pattern which is Left →
Center → Right → Surround Right → Surround Back
Right → Surround Back Left → Surround Left →
Subwoofer → Left → ...in increments of 3 seconds
for each channel.
If you select MANUAL, press the ok button to cycle
through the test tone channels after the “TEST
TONE ON”.
TEST TONE: Press the ok button, ON is indicated and the test
tone starts from the front left speaker.
Notes : Master volume level will be automatically
set at the 0 dB position.
Level adjust : Adjust the level of the test tone for each channel
with the LVL+, LVL– or, <, > buttons of the RC5000i.
The current volume level is shown at the center of
the display.
Notes:
• The setup level for each channel is memorized for reproduction
in all surround mode.
• These levels are common for all surround modes, except 6CH-
INPUT mode.
• In order to correctly set the output levels, use a hand-held
Sound Pressure Level meter (SPL), set to C-Weighting and Slow
averaging.
• A Radio Shack
®
SPL meter (catalogue number 330 - 2055)
works well.
• Using the internal channel noise generators, set each channel so
that you read 75 dB SPL from each channel when seated at the
listening position.
LEVELS SETUP 2/2 (BASS PEAK LEVEL LIMIT)
With Dolby Digital and DTS , not only the LFE (Low Frequency
Effects), but also the bass of all channels can be heard from the
Subwoofer or Large-speakers. This procedure prevents these
speakers from becoming too loud and creating an unbalanced
sound. Since the sound is output at a loud volume, perform this
operation carefully.
TEST SIGNAL: Press the ok button, START is indicated and it
begins to generate a Bass test tone from the
speaker which was designated “bass signal output”
during setup.
There will be no audible sound yet because the
Master volume is set to minimum automatically.
Press v button to move the cursor to VOLUME control.
VOLUME: Adjust the bass test tone output level up until the
bass begins to distort or you reach the maximum
level with the VOL+, VOL– or </ > button. Press v
button to move the cursor to ENTER.
ENTER: Press the ok button, ENTER will blink and stop
generating the Bass - test tone.
The Bass Peak Limit Level for your system has now
been memorized.
Notes:
• Each time the subwoofer level is changed, perform the Bass
Peak Level setup and correct the setting.
• The bass peak limiter is not effective in STEREO, SOURCE-
DIRECT 5ch STEREO, and 6CHANNEL-INPUT mode.
• The selected value is displayed in the volume column before the
test signal starts.
SE
:
C
S
1
1
SK SR
TI
TUPP
UN
2/2
10
L
B
0
SL
SL
10
1
ft
R
10
1
0SW
0
B
:
SR
10R
0
SB
0
E
1
EX IRUNTER NTER T
S
O
LS
E
S
C
0
LV
D
E
M
ETUE
TS
S
T
T
E
1/2
L
:
L
T
0
E
BL
SL
S100
ON
:M
P
ANUA
R
0SW
0
SR
R 1 0
0
B
0 0
SB
NTXE
S
P
LS
A
R
A
LV
E
N
––
E
E
S
E
K
TUE
A
M
T
U
SB
2/2
TS
E
E
O
S
L
––––
V
E
––––
IG
NT
LE
P
VEL
A
5
T
: –
R
Bd
L
–
:ST
7
–––––––––
EX ITRUNTER
… 22 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Marantz SR14 MKII wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info