Bedienungsanleitung Marantz SR4003 (Seite 27 von 48) (Englisch)

61338

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

ENGLISH

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

NAMES AND

FUNCTIONS

SETUP

3 PREFERENCE

STANDBY MODE : ECONOMY

TV-AUTO :

OSD INFO : ENABLE

VIDEO CONVERT

HDMI : ENABLE

MAIN EXIT

Select “PREFERENCE” in the SETUP MAIN

MENU with the 3 or 4 cursor buttons, and

press the ENTER button.

To select a desired content, press the 3 or 4

cursor buttons.

STANDBY MODE:

When this function is set to “ECONOMY”, you can

reduce the power consumption when the unit is in

the standby mode.

Note:

TV-AUTO is disabled in the “ECONOMY” setting.

TV AUTO:

Select the TV AUTO ON/OFF function to enable or

disable with the 1 or 2 cursor buttons.

OSD Info:

Select the OSD information function to enable or

disable with the 1 or 2 cursor buttons.

If you select “ENABLE”, the unit will display the

status of the feature (Volume up/down, input

select, etc..) on the TV monitor. But if you do not

desire this information, select “DISABLE”.

VIDEO CONVERT:

Select the VIDEO CONVERT function to enable or

disable with the 1 or 2 cursor buttons. (Video cable

connection: Refer to page 12)

3-1 VIDEO CONVERT

TV : ON

DVD : ON

VCR : ON

DSS : ON

AUX1 : ON

MAIN RETURN EXIT

After you complete this portion of the set up, move

the cursor to “MAIN” with the 3 or 4 cursor buttons

and press the

ENTER

button.

HDMI AUDIO:

This setting determines whether to playback audio

input to the HDMI jacks through the unit or output

it through the unit to a TV or projector.

ENABLE: The audio input to the HDMI jacks

can be played back by this unit.

In such case, audio signals are not

output to the TV or projector.

THROUGH: The audio input to the HDMI jacks

is not output from the speaker

terminals of the unit. Audio data is

output directly to the TV or projector.

This setting is used to listen to audio

on a multi channel TV, etc.

4 SURROUND

SURR.MODE :AUTO

HT-EQ :OFF

LFE LEVEL :

MAIN EXIT

Select “SURROUND” in the SETUP MAIN

MENU with the 3 or 4 cursor buttons, and

press the ENTER button.

To select a desired content , press the 3 or 4

cursor buttons.

SURR.MODE:

Select the desired surround mode with the 1 or 2

cursor buttons.

HT-EQ:

Select to active the HT-EQ with the

1 or 2

cursor

buttons.

The tonal balance of a film soundtrack will be

excessively bright and harsh when played back

over audio equipment in the home. This is because

ﬁ lm soundtracks were designed to be played back

in large movie theater environments.

Activating the HT-EQ feature when watching a ﬁ lm

made for movie theaters corrects this and restores

the correct tonal balance.

The HT-EQ feature is available except in the

following modes.

• 7.1 CH INPUT

• PURE-DIRECT

• SOURCE DIRECT

• When VIRTUAL is set for the surround mode

LFE LEVEL:

Select the output level of the LFE signal included in

the Dolby Digital signal or the DTS signal.

Select 0 dB, -10 dB or OFF with the 1 or 2 cursor

buttons.

After you complete this portion of the set up, move

the cursor to “MAIN” with the 3 or 4 cursor buttons

and press the ENTER button.

Notes:

• The measured speaker distance may differ from the

actual distance from speakers. Nevertheless, the

measured value is suitable for the speakers.

• To make changes to individual speakers, select 2.

SPEAKER SETUP on the SETUP MAIN MENU,

then select MANUAL for 2-1 SPEAKER SETUP.

• The included microphone is designed speciﬁ cally for

this receiver. Other microphones do not guarantee

suitable measurement results. Use the included

microphone to conduct measurements.

• During measurement, press the ENTER or EXIT

button to cancel measurement.

• In some rooms, an error may occur during auto

speaker setup or it may not be possible to set Speaker

distance correctly because of room acoustics. In

such case, set the speaker distance by MANUAL

setup.

• Please set any THX Certiﬁ ed speakers manually

to “Small” and the crossover to “80 Hz” after Auto

setup operation.

• When only HDMI components are connected, OSD

will not be displayed.

Error Indications During Measurement

If trouble occurs during measurement, an error

message is displayed on the monitor screen and

FL display. Those errors and their remedies are

described below. The message appearing on the FL

display is given in ( ).

MIC SETUP ERROR (MIC SET ERROR)

The microphone (MC-10) is not properly connected.

→ Check the microphone connection.

AMBI NOISE ERROR (AMBI NOISE ER)

Measurement cannot be done correctly because of

excessive ambient noise.

→ Either temporarily turn off power to noisy

devices such as air conditioning or move them

out of the room.

→ Retry measurement when the room is quiet.

SPEAKER SET ERROR (SPK SET ERROR)

The speakers are not properly connected.

→ Recheck speaker layout and connections.

SR4003_U_01_E2_2.indd 24SR4003_U_01_E2_2.indd 24 08.6.20 5:06:27 PM08.6.20 5:06:27 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR4003 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR4003

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info