Bedienungsanleitung Marantz SR5004 (Seite 30 von 96) (Englisch)

522801

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

NAMES AND

FUNCTIONS

BASIC

CONNECTIONS

BASIC

OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERSSETUP

ENGLISH

SETUP

HOW TO PERFORM AUTO SETUP

(AUDYSSEY MULTEQ

)

During this setup process, a GUI menu displays

important instructions. So be sure to connect and

power on the monitor to view the GUI instructions.

1. Connect the supplied microphone to the

SETUP MIC jack on the unit.

2. Set the microphone in the main listening

position.

Notes

• Up to 6 positions around the main listening

position can be measured.

For the ﬁ rst measurement, set the microphone in

the main listening position.

• Use a stand or tripod to position the microphone

at ear height for all listening positions measured

with the microphone tip pointing directly up to the

ceiling.

• Remove any obstructions between the speakers

and microphone.

• When using a powered subwoofer, set the level

knob to the middle or 12 o'clock position. Set the

crossover to off, or to its highest value.

If the subwoofer has a standby, or sleep mode,

disable it. Not doing so could affect the test

signal which may result in inaccurate subwoofer

measurements.

• During measurements, do not stand between the

microphone and the speakers. Make the room as

quiet as possible. Background noise can disrupt

the room measurements. Close windows, silence

cell phones, televisions, radios, air conditioners,

ﬂ uorescent lights, home appliances, light dimmers,

or other devices.

Cell phones should be placed away from all audio

electronics during the measurement process as

Radio Frequency Interference (RFI) may cause

measurement disruptions (even if the cell phone

is not in use).

It is suggested to operate the AUTO SETUP via

the remote controller rather than by front panel.

• The test tones played through each channel

increase level as needed in order to overcome

ambient noise present in the listening environment

and obtain the best signal to noise ratio.

3. Select “Speaker Setup” from the Main

Menu, select “Auto Setup” with the 3/4

cursor buttons, and press the ENTER button

to display the start screen.

4. Select the number of channels of the

surround back speakers which are being

used and whether height speakers are

part of the system. When a 5.1-channel

configuration is used for the speaker

systems, select “NONE” (no surround back

speakers and no front height speakers).

(See page 21, 36.)

Select “Start” with the 3/4 cursor buttons

and press the ENTER button to start

measurement.

Audyssey MultEQ Setup

StartManual Setup

Front Height

Surround Back

Return

: Up / Down : Enter : OK Exit : Exit

: Yes

: 2ch

5. “1st Mic Position Check”

The main listening position refers to the most

central position where one would normally

sit within the listening environment.

MultEQ uses the measurements from this

position to calculate speaker distance,

level, polarity, and the optimum crossover

value for the subwoofer.

Audyssey MultEQ Setup

Cancel

Speaker Check :

1st Mic Position

Now Analyzing!!

: : Enter : OK Exit : Exit

Note

• The Speakers Check detects the presence of

connected speakers. If a channel is not used, the

SPEAKERS CHECK will try to detect it, then

continue to the next channel.

6. When the 1st Mic Position Check ends, the

following GUI appears on the display.

Audyssey MultEQ Setup

Start

Check

Calculate

Speaker Check : OK

2nd Mic Position

: Up / Down : Enter : OK Exit : Exit

Here, to view the results of the detection

check, select “Check” with the 3/4 cursor

buttons and press the ENTER button. The

results will be displayed.

Speakers Configuration

Check Speaker Results

Front Left

Front Height Left

Center

Front Height Right

Front Right

Surround Right

Surround Back

Surround Left

Subwoofer

Return

: : Enter : Return Exit : Exit

: Yes

: No

: Yes

: No

: Yes

If Check Speaker Results indicates an error,

address the issue of the noted speaker

and remeasure. (For error messages, see

“ERROR MESSAGES” on page 30.)

After conﬁ rming the check results, select

“Return” with the 3/4 cursor buttons and

press the ENTER button to return to the GUI

menu.

At this point, you can select “Exit” to

end Auto Setup and return to “Speaker

Setup”.

Note

• Auto Setup is not available in Pure Direct, Source

Direct, or 7.1 Channel Input modes.

7. Move the microphone to the 2nd listening

position, select “Start” with the 3/4 cursor

buttons and press the ENTER button to

measure the 2nd point. At this point, you

can cancel second point measurement

and calculate measurement results by

selecting “Calculate” and pressing the

ENTER button.

Audyssey MultEQ Setup

Start

Check

Calculate

Speaker Check : OK

2nd Mic Position

: Up / Down : Enter : OK Exit : Exit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR5004 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info