62166

Marantz SR7002 Seite 23

23
Zoom out
Zoom in
Vorherige Seite
1/94
Nächste Seite
ENGLISH
20
Erasing All
This procedure clears (resets) all programmed
codes and names. Once all the data is cleared, the
memory is returned to the factory default status. The
programmed macros are also erased.
1 3 4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
1 23
4
LEARN
NAME
MACRO
USE
PAG E
123
4
1.
Hold down the M button for three seconds or
more.
The menu is displayed.
2.
Press the D5 (ERASE) direct button .
The
USE
and
LEARN
indicators blink.
3.
Press the CLEAR button while holding down
the POWER ON and OFF buttons at the same
time.
4.
Press the D4 (YES) direct button to erase.
All programmed codes and names are erased and
reset to the factory default settings.
• To cancel the erasing operation, press the
D5 (NO) button to return to the previous
screen.
• To erase all operation takes a few seconds
after the D4 (YES) button is pressed.
PROGRAMMING MACROS
This remote controller can program a series of button
operations in sequence.
Macros are a function that makes it possible to
use a single button operation to perform a complex
series of button operations any number of times. A
single button can be programmed to perform up to
20 steps in sequence. A total of 20 buttons can be
programmed with macros.
• For example, the following sequence of operations
can be programmed to a macro.
Switch amplifi er to DVD source → Set amplifi er
mode to AUTO → Play DVD player → Switch TV
to video input
The factory default for the transmission interval
(time) between macro operations is one second,
but these signal transmission intervals can be set
between approximately 0.5 seconds and 5 seconds
in the Setup mode. Each transmission interval can
be adjusted independently when programming or
revising a macro.
Note:
• If the signal transmission interval (interval time)
is changed using the Setup mode (described later),
this transmission interval is applied to all macro
programs. To change individual signal transmission
intervals, use the procedures in this section for
programming macros and revising macros.
• No signals are transmitted while programming a
macro.
• The M button, > button, cursor buttons, MEMO
button, CLEAR button, and VOL buttons cannot
be programmed.
• If no button is pressed for approximately one
minute during programming, the remote controller
returns to the state before macro mode.
In this case, the macro program is not stored.
• When executing macro mode, performing the
source switching operation two or more times
only changes the remote control mode and does
not transmit any signals. (Switching of the source
selector of the amplifi er is valid only once.)
PROGRAMMING MACROS
This example shows how to program a macro to the
M-01 button.
(The screens shown in the example are the default
factory states. If the names of direct buttons
were rewritten, these modified names would be
displayed.)
Switch amplifi er to DVD source → Play DVD player
→ Set the interval to 2 seconds until the next signal is
sent → Switch TV to video input → Set the amplifi er
mode to AUTO
1 2 3
LEARN
NAME
MACRO
USE
PAG E
1 23
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
1.
Hold down the M button for three seconds or
more.
The menu is displayed.
2.
Press the D4 (MACRO) direct button .
The macro menu is displayed.
The
MACRO
indicator displays and
LEARN
blinks.
3.
Press the D1 (M-01) direct button .
The menu has four pages, and so use the
>
button
to select the page when programming other buttons.
4.
Press the buttons in the sequence that you
want the operations performed.
The actual program starts here.
Each time a button is pressed, the name of the
button is displayed on the LCD.
4-1 4-2 4-3
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
4-1.
Press the DVD source button .
4-2.
Press the 2 (PLAY) button .
4-3.
Press the 3 or 4 cursor buttons .
The interval time is displayed on the LCD.
4-4.
Press the 3 or 4 cursor buttons and set to 2.0
(seconds).
• Use the 3 cursor button to increase the time
and the 4 button to decrease the time. The
interval time can be set from 0.5 seconds to
5 seconds.
• To stop the time adjustment, press the D5
(CANCEL) direct button.
4-5.
Press the OK cursor button .
4-6.
Press the TV source button .
4-7.
Press the > button to display the fi rst page.
4-8.
Press the D1 (INPUT) direct button .
4-9.
Press the AMP source button .
4-
10
.
Press the > button to display the fi rst page.
4-
11
.
Press the D1 (AUTO) direct button .
4-
12
.
Press the OK cursor button .
The LCD displays END to indicate that programming
is completed.
5.
To program another macro, repeat the
procedure in steps 3 to 4-12.
6.
To exit macro programming, press the M button
.
The
USE
indicator displays to indicate that the
remote controller can now be operated.
When the macro are programmed 20 operations or
more, the display returns macro menu.
Edit the macro so that it has 20 operations or less.
EXECUTING MACRO PROGRAMS
1 2 3
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
1.
Press the M button shortly.
The macro menu is displayed.
2.
Press the D1 (M-01) direct button .
3.
Check that the operations of the program are
executed step by step.
The name of the operation button is displayed on
the LCD.
• The programmed section is indicated by
&. The bar indicator moves to indicate the
progress of the program.
Select DVD source
→
PLAY transmit
→
Interval
time: 2 seconds
→
Select TV
→
TV INPUT transmit
→
Select AMP
→
AUTO transmit
→
End
• To cancel transmission of the program while
it is in progress, press any button.
CHANGING NAMES OF MACRO PROGRAMS
Under the factory default settings, the names of the
macro programs are set from M-01 to M-20, but you
can change them to any desired name.
The text can have up to six characters, and it is
entered using the numeric buttons.
This example shows how to change the M-01 name
to MOVIE.
1 2 3
LEARN
NAME
MACRO
USE
PAG E
1 23
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
4 5 6
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
LEARN
NAME
MACRO
USE
PAG E
123
4
1.
Hold down the M button for three seconds or
more.
The menu is displayed.
SR7002-8002_U_01_ENG 1_3.indd 20SR7002-8002_U_01_ENG 1_3.indd 20 07.8.24 1:14:51 PM07.8.24 1:14:51 PM
… 23 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Marantz SR7002 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Marantz SR7002

Marantz SR7002 Bedienungsanleitung - Holländisch - 74 seiten

Marantz SR7002 Bedienungsanleitung - Französisch - 84 seiten

Marantz SR7002 Bedienungsanleitung - Spanisch - 84 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info