Bedienungsanleitung Marin Bikes (Seite 17 von 54) (Englisch)

780517

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

tube with the tip of your nger without inserting your nger beyond its rst

knuckle. Also see NOTE above and g. 5).

WARNING: If your seat post is

not inserted in the seat tube as

described in B.1 above, the

seat post may break, which

could cause you to lose control

and fall.

2. Front and back adjustment

The saddle can be adjusted forward

or back to help you get the optimal

position on the bike. Ask your dealer to

set the saddle for your optimal riding

position and to show you how to make

this adjustment. If you choose to make

your own front and back adjustment,

make sure that the clamp mechanism is clamping on the straight part of the

saddle rails and is not touching the curved part of the rails, and that you

are using the recommended torque on the clamping fastener(s) (Appendix

D or the manufacturer’s instructions).

3. Saddle angle adjustment

Most people prefer a horizontal saddle; but some riders like the saddle

nose angled up or down just a little. Your dealer can adjust saddle angle

or teach you how to do it. If you choose to make your own saddle angle

adjustment and you have a single bolt saddle clamp on your seat post, it is

critical that you loosen the clamp bolt sufciently to allow any serrations on

the mechanism to disengage before changing the saddle’s angle, and then

that the serrations fully re-engage before you tighten the clamp bolt to the

recommended torque (Appendix D or the manufacturer’s instructions).

hips must rock for the heel to reach the pedal, the saddle is too high. If your

leg is bent at the knee with your heel on the pedal, the saddle is too low.

Ask your dealer to set the saddle for your optimal riding position and to

show you how to make this adjustment. If you choose to make your own

saddle height adjustment:

 loosen the seat post clamp

 raise or lower the seat post in the seat tube

 make sure the saddle is straight fore and aft

 re-tighten the seat post clamp to the

recommended torque (Appendix D or the

manufacturer’s instructions).

Once the saddle is at the correct height,

make sure that the seat post does

not project from the frame beyond

its “Minimum Insertion” or “Maximum

Extension” mark (g. 4).

NOTE: Some bicycles have a sight hole

in the seat tube, the purpose of which

is to make it easy to see whether the

seat post is inserted in the seat tube far

enough to be safe. If your bicycle has

such a sight hole, use it instead of the “Minimum Insertion” or “Maximum

Extension” mark to make sure the seat post is inserted in the seat tube far

enough to be visible through the sight hole.

If your bike has an interrupted seat tube, as is the case on some suspension

bikes, you must also make sure that the seat post is far enough into the

frame so that you can touch it through the bottom of the interrupted seat

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marin Bikes Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info