Bedienungsanleitung Marmitek MS13 (Seite 3 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

494268

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

MS13E – WIRELESS MOTION SENSOR

SAFETY WARNINGS

• Do not expose the components of your systems to extremely high temperatures or bright light sources.

• The product should only be repaired or serviced by a qualified repairman.

• In case of improper usage or if you have opened, altered and repaired the product yourself, all

guarantees expire. Marmitek does not accept responsibility in the case of improper usage of the

product or when the product is used for purposes other than specified. Marmitek does not accept

responsibility for additional damage other than covered by the legal product responsibility.

• Batteries: keep batteries out of the reach of children. Dispose of batteries as chemical waste. Never use

old and new batteries or different types of batteries together. Remove the batteries when you are not

using the system for a longer period of time. Check the polarity (+/-) of the batteries when inserting

them in the product. Wrong positioning can cause an explosion.

• This product is not a toy. Keep out of reach of children.

• Automatic switching devices provide comfort, but can also be dangerous. They can surprise people or

can ignite clothing hanging over an electric heat source. Please be careful and take appropriate

measures to avoid accidents.

HOW DOES MARMITEK X-10 WORK?

Marmitek X-10 components use the existing mains wiring to communicate (using Marmitek X-10 signals).

You can build a complete system using the three different kind of components of the Marmitek X-10

System:

1. Modules: These components will receive Marmitek X-10 signals and will switch or dim the

attached lamp or appliance.

2. Controllers: These components will transmit Marmitek X-10 signals and thus will control the Modules.

3. Transmitters: Wireless components like remotes. The signals of these components will be received by

a controller with transceiver functionality (IRRF 7243, TM13 or console of a Marmitek

Security System). The Transceiver will translate the signals into Marmitek X-10 signals on

the power line.

ADRESSES

Up to a maximum of 256 different addresses can be preset. These are subdivided into a so-called

HouseCode (A to P incl.) and a UnitCode (1 to 16 incl.). The HouseCode can also be set on the controllers,

so that the controllers and modules become part of the same system. The address can be set either using

code dials or by pressing buttons, depending on the type of module.

The Marmitek X-10 System uses standard commands, which control all units with the same HouseCode at

the same time (e.g. all lights on, all off, etc.).

SIGNAL RANGE

Range of Marmitek X-10 signals over the Power Line and how to increase the range.

The Marmitek X-10 System is based on power line communication. The range of the Marmitek X-10 signals

very much depends on the local circumstances. On average the range is a cable length of 80 meters.

If you have difficulties with the range of your Marmitek X-10 signals, please pay attention to the

following facts:

3MS13

ENGLISH

manual MS13 05-12-2006 09:54 Pagina 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek MS13 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info