Bedienungsanleitung Marmitek MS13 (Seite 5 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

494268

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

The MS13 is fully wireless, the signal is transmitted straight through walls and ceilings and it is

suitable for outdoor use.

OPERATION

The MS13 motion detector sends radio signals to an X10 transceiver (Marmitek X10 TM13 or Marmitek X10

Alarm station). The transceiver or station then transmits these signals wirelessly via the electric cabling that is

already in your house to switch lights (or appliances) that are connected to X10 receivers on and off. The

Marmitek X10 TM13 and a Marmitek X10 CM11 computer interface can also be used to activate previously

programmed macros. The MS13 can also be programmed to detect motion both at night and during the day,

or only at night. The Marmitek X10 MS13 can also be used to detect the transition from light to dark and

vice versa.

INSTALLATION

Slide the antenna sleeve over the sensor’s wire antenna. Press the sleeve into the clamp on the top of the

sensor. Insert 2 AAA batteries into the MS13’s battery compartment. The cap on the front of the sensor

must be removed using tweezers or small pliers in order to open the battery compartment. Now the screw

that is locking the lid can be unscrewed. Replace the cap if the sensor is to be used outdoors.

• After inserting the batteries it will take 30 seconds for the MS13 to become active.

• After a signal has been transmitted the MS13 will be inactive for 10 seconds.

• The default setting for the house-code that is transmitted is A (factory setting).

• The default setting for the unit-code that is transmitted for motion detection is 1 (factory setting).

• The unit-code that is transmitted for light / dark detection is always the unit-code that has been set + 1

(example: If you have the motion detection code set to A3 the code for light/dark is automatically A4).

The default setting for this function is off (factory setting).

• When motion is detected an <on> command is transmitted.

• When the <house/on> button is pressed once an <on> command is transmitted.

• When the <unit/off> button is pressed once an <off> command is transmitted.

• On transition from light to dark an <on> command is transmitted for the unit-code that has been

set +1.

• On transition from dark to light an <off> command is transmitted for the unit-code that has been

set +1.

• When motion is detected an <on> command is transmitted for the unit code that has been set.

• After the last motion detection plus the set delay (factory setting 1 minute) an <off> command is

transmitted for the unit code that has been set.

PROGRAMMING THE HOUSE-CODE

Unlike most Marmitek X-10 Modules the MS13 does not have code wheels.

• Press the <house/on> button and hold it down.

• The red LED will start to flash.

• 3 seconds later the LED will display the current house-code setting (the factory setting is A).

• 1 flash for A.

• 2 flashes for B.

• …

• 16 flashes for P.

• Release the <house/on> button.

5MS13

ENGLISH

manual MS13 05-12-2006 09:54 Pagina 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek MS13 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info