Bedienungsanleitung Marmitek MS13 (Seite 6 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

494268

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

• Now press the <house/on> button the number of times that corresponds to the house-code that you

want to set. On the last press hold down the button (e.g. for house-code C press the <house/on>

button 3 times and hold the button down on the third press).

• After 3 seconds the LED will display the new setting. If you wait too long, or if an error occurs, the red

LED will flash rapidly. In this case no changes are implemented and you should start again from the

beginning.

PROGRAMMING THE UNIT-CODE

• Press the <unit/off> button and hold it down.

• The red LED will start to flash.

• 3 seconds later the LED will display the current unit-code setting (the factory setting is 1).

• 1 flash for 1.

• 2 flashes for 2.

• …

• 16 flashes for 16.

• Release the <unit/off> button.

• Now press the <unit/off> button the number of times that corresponds to the unit-code that you want to

set. On the last press hold down the button (e.g. for unit-code 3 press the <unit/off> button 3 times and

hold the button down on the third press).

• After 3 seconds the LED will display the new setting. If you wait too long, or if an error occurs, the red LED

will flash rapidly. In this case no changes are implemented and you should start again from the beginning.

SETTING THE SENSOR FOR DAY/NIGHT USE

• Press the <unit/off> button once.

• The LED will flash briefly.

• Press the <house/on> button and hold it down.

• The green LED behind the PIR lens will light up.

• 3 seconds later the LED will display the current mode (the factory setting is 1).

• 1 flash when the motion detector is on during the day, light/dark sensor off.

• 2 flashes when the motion detector is off during the day, light/dark sensor off.

• 3 flashes when the motion detector is on during the day, light/dark sensor on.

• 4 flashes when the motion detector is off during the day, light/dark sensor on.

• Release the <house/on> button.

• Now press the <house/on> button the number of times that corresponds to the mode that you want

to set. On the last press hold down the button (e.g. for mode 3 press the <house/on> button 3 times

and hold the button down on the third press).

• After 3 seconds the LED will display the new setting and the LED will switch off.

SETTING THE DELAY TIME

(the length of time that the lamp will remain illuminated after the last motion has been detected)

• Press the <house/on> button once.

• The LED will flash briefly.

• Press the <unit/off> button and hold it down.

• The green LED behind the PIR lens will light up.

• 3 seconds later the LED will display the current mode (the factory setting is 1):

• 1 flash for 1 minute.

• 2 flashes for 2 minutes.

• 3 flashes for 4 minutes.

6 © MARMITEK

manual MS13 05-12-2006 09:54 Pagina 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek MS13 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info