494268
7
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
4 flashes for 8 minutes.
5 flashes for 16 minutes.
6 flashes for 32 minutes.
7 flashes for 62 minutes.
8 flashes for 128 minutes.
9 flashes for 255 minutes.
Release the <unit/off> button.
Now press the <unit/off> button the number of times that corresponds to the mode that you want to
set. On the last press hold down the button (e.g. for a 4-minute delay press the <unit/off> button 3
times and hold the button down on the third press)
After 3 seconds the LED will display the new setting and the LED will switch off.
The MS13 saves the settings in non-volatile memory so that the settings are kept when the batteries are
changed.
NOTE: The MS13 cannot activate alarm functions on Marmitek Alarm systems. Use the MS90 for this.
FREQUENTLY ASKED QUESTIONS
What is the reason for modules to switch on/off spontaneously?
It is possible that a Marmitek X-10 System is installed at one of your neighbours using the same House
Code. To solve this problem try to change the House Code of your system, or have FD10 Phase
Coupler/Filter installed at your incoming mains.
My modules will not respond to my controller.
Make sure that the House Code on all Modules and Controllers are set to the same House Code (A .. P).
My modules will not react to my remote / sensor.
When you use a remote or sensor, you should have at least one TM13 Transceiver or Marmitek Security
Console installed in your house. These components will translate the radio signals to the Marmitek X-10
signal on the power line. Only one Transceiver should be installed for all remotes and sensors set to the
same House Code.
Am I able to increase the range of my remotes by using more Transceivers?
Yes, you can use more than one TM13 Transceiver in your home when the range of your remotes is not
sufficient. The TM13 is using so called collision detection to prevent signals to be disturbed when more
than one TM13 is transmitting. TM13’s will wait for a quite power line before transmitting their data. To
prevent your Marmitek X-10 System to become slow or to prevent dimming from becoming less smooth,
make sure that the TM13 units are placed as far away from each other as possible.
Do you still have questions?
Please check out www.marmitek.com for more information.
TECHNICAL SPECIFICATIONS
Power supply: 2x AAA battery
RF frequency: 433.92 MHz
RF Range: Up to 30m free field, up to 20m through walls and ceilings
RF Power: 1mW
PIR range: 45º - 5 metres, straight ahead - 12 metres
Ambient temperature: - 10°C to + 30° C (operation) - 20°C to + 70° C (storage)
Dimensions: 67x67x27mm
7MS13
TM
ENGLISH
manual MS13 05-12-2006 09:54 Pagina 7
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Marmitek MS13 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info