Bedienungsanleitung Marmitek SW10 (Seite 5 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

494308

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENGLISH

5SW10

My modules will not respond to my controller.

Make sure that the House Code on all Modules and Controllers are set to the same House

Code (A .. P).

My modules will not react to my remote / sensor.

When you use a remote or sensor, you should have at least one TM13 Transceiver or

Marmitek Security Console installed in your house. These components will translate the radio

signals to the Marmitek X-10 signal on the power line. Only one Transceiver should be

installed for all remotes and sensors set to the same House Code.

Am I able to increase the range of my remotes by using more Transceivers?

Yes, you can use more than one TM13 Transceiver in your home when the range of your

remotes is not sufficient. The TM13 is using so called collision detection to prevent signals to

be disturbed when more than one TM13 is transmitting. TM13’s will wait for a quite power

line before transmitting their data. To prevent your Marmitek X-10 System to become slow or

to prevent dimming from becoming less smooth, make sure that the TM13 units are placed as

far away from each other as possible.

USER INSTRUCTIONS SW10 SHUTTER SWITCH

SWITCH OFF APPROPRIATE MAINS FUSE BEFORE INSTALLING!

(INSTALLATION BY A CERTIFIED INSTALLER)

1. Take of the switch cover, remove both screws and take off the mounting plate.

2. Mount the mounting plate onto the flush mounting box with countersunk screws.

Position the plastic décor frame.

3. Connect cables:

Phase to L (_)

Neutral to N

UP to UP

Down to DN

4. When connected, position Shutter Switch on the mounting plate and reinsert both screws.

5. Now program the switch using the following procedure:

PROGRAMMING THE SW10

Now the control electronics has to be calibrated in order to adjust to the time the shutter

motor need from fully closed to fully open:

1. Switch on mains fuse.

2. Use the switch to drive the shutter all the way up.

3. With the aid of a screwdriver, adjust the House Code dial to the * position.

4. Now press the lower push button until the shutter is closed completely.

5. Release the button as soon as the shutter is closed. The electronics measure the elapsed

time and stores it internally so that the switch always knows the position of the shutter.

6. Set the rotary code switches on the front side to the desired address

7. Put the switch cover back on.

The calibration is now completed. The internal electronics have measured and stored the time

for raising and lowering the shutter. These values will not be lost even in case of mains fail-

ure. You are now able to control the switch both by hand and with a Marmitek X-10

Controller (the switch will not respond to Marmitek X-10 signals when the programming has

not been executed).

The switch will respond to the following commands: ON: fully open, OFF: fully closed,

DIM : 4 % up, BRIGHT: 4 % down.

SW10.qxd 02-11-2006 17:20 Pagina 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek SW10 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info