Bedienungsanleitung Masterpro BGMP9132 (Seite 18 von 55) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

797872

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

CLEANING AND MAINTENANCE

• Before you clean the device, unplug it.

• The blades are sharp. Be careful when you clean blade units.

• Make sure that the cutting edges of the blades do not come into contact with hard objects. This may

cause the cutting edges to become blunt.

• Clean the motor unit with a damp cloth and dry thoroughly.

• Clean other parts in lukewarm water with some cleaning agent or in a dishwasher. Refer to the

cleaning table.

• If ingredients dry inside the blending vessels, fill the cups about 2/3 full with warm soapy water.

Assemble according to the instructions and blend the content for 20-30 seconds. Scrub gently and

rinse.

• Clean the 6 wing blade assembly rubber gasket regularly. Grab and lift the gasket from the base

and wash under warm water.

• Before storing the device you can wind the cable in cable storage at the bottom of the device.

TROUBLESHOOTING

EN EN

1. Fill in the ingredients up to

the MAX level marked on the

cup.

2. Cover the jug with lid and lock it in (rotate it clockwise) position where arrows on the lid and jug’s

handle align.

3. Lift the jug onto the main unit and press

it slightly down until your hear »click«

sound, which indicates that the jug is

connected properly.

4. Press the HEATING BLEND MODE button and

the mode light will start to flash. Press the button to

start the HEATING BLEND cycle, you will hear the

beep sound and the mode light will turn on. After

the cycle is completed, the device will stop and

switch to stand by mode automatically.

Quickly double tap will switch to lower temperature and tap one more time will switch to

medium temperature.

NOTE: The content after finished cycle is hot. Open the lid carefully to prevent scalding. Do not open

the lid During the HEATING BLEND cycle.

5. Remove the jug from the unit and open the lid (turn counter clockwise )with caution as the content

is hot.

HEAT BLENDING

NOTE: The content should

never exceed the MAX level.

IMPORTANT NOTE – OVERHEATING PROTECTION: To maintain the device at its best

performance and to prolong the motor life, the total operating time of the unit is 230s, which for

example is 6 cycles in BLEND mode. After the max operating time is reached, the device will turn off

automatically to cool down for 10 min, before it can be used again.

MAX

For best performance the recommended food

should be in cubes of 1 x 1 x 1 cm.

Heat Blending cycle (heating up to max 70 °C +15

min cooking at 70°C + 3 x pulsing + 90 s blending).

TIPS & RECOMMENDATION

• Due to the high friction created in cup by the blades the content temperature could raise slightly. To

prevent this, an ice cube or two can be added to maintain the temperature.

• If the food sticks to the wall of the blender jar, switch off the appliance and unplug it. Then use soft

spatula (not supplied with the product) to remove the food from the wall.

• The potatoes for creamy soups should be precooked.

• If ingredients get stuck in the 700 ml, remove them from the base, shake or tap it slightly and

continue with the process.

14 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Masterpro BGMP9132 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info