Bedienungsanleitung Masterpro BGMP9132 (Seite 19 von 55) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

797872

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

CLEANING AND MAINTENANCE

• Before you clean the device, unplug it.

• The blades are sharp. Be careful when you clean blade units.

• Make sure that the cutting edges of the blades do not come into contact with hard objects. This may

cause the cutting edges to become blunt.

• Clean the motor unit with a damp cloth and dry thoroughly.

• Clean other parts in lukewarm water with some cleaning agent or in a dishwasher. Refer to the

cleaning table.

• If ingredients dry inside the blending vessels, fill the cups about 2/3 full with warm soapy water.

Assemble according to the instructions and blend the content for 20-30 seconds. Scrub gently and

rinse.

• Clean the 6 wing blade assembly rubber gasket regularly. Grab and lift the gasket from the base

and wash under warm water.

• Before storing the device you can wind the cable in cable storage at the bottom of the device.

TROUBLESHOOTING

TIPS & RECOMMENDATION

• Due to the high friction created in cup by the blades the content temperature could raise slightly. To

prevent this, an ice cube or two can be added to maintain the temperature.

• If the food sticks to the wall of the blender jar, switch off the appliance and unplug it. Then use soft

spatula (not supplied with the product) to remove the food from the wall.

• The potatoes for creamy soups should be precooked.

• If ingredients get stuck in the 700 ml, remove them from the base, shake or tap it slightly and

continue with the process.

SYMBOL CHART

ISSUE POSSIBLE SOLUTION

The device does not start to work. Check if the plug is properly inserted into the power supply socket.

Check if all the removable parts are properly assembled.

The smoke comes out of the air vent. Stop and unplug the appliance immediately. Leave to cool down

for 15 minutes before further use.

The device stopped working during

the cycle.

Total continuous operation time 230 s could be exceeded. Set to

mode 0, unplug it and leave to cool down for 10 minutes. STOP

CAUTION! Rotating parts. Do not touch, clean or replace before unplugging the device

from power supply.

Regular cleaning is necessary. Inspect and clean any spillages, residues or dirt after

each use.

Failing to do that could greatly reduce performance of the device and/or increase the

possibility of device or personal damage.

Do not immerse in water/liquid.

Indoor use only.

Make sure you have read and fully undersood user manual before operating this device.

Unplug from power supply before parts assembly or cleaning.

CAUTION: Do not exceed maximum allowed operating and rest time.

CAUTION: Danger of overheating if maximum operating time is surpassed or hot content

is grinded.

Do not attempt any modification or repair by yourself.

CAUTION! Sharp objects. Use extreme care.

CAUTION! Hot surface.

Not dishwasher safe.

16 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Masterpro BGMP9132 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info