Bedienungsanleitung Max 31131 (Seite 51 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

789310

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Feed workpiece at an even pace. Do not

bend or twist the workpiece. If jamming

occurs, turn the tool o immediately, unplug

the tool then clear the jam. Jamming the saw

blade by the workpiece can cause kickback

or stall the motor.

Do not remove pieces of cut-o material

while the saw is running. The material may

become trapped between the fence or insi-

de the saw blade guard and the saw blade

pulling your ngers into the saw blade. Turn

the saw o and wait until the saw blade stops

before removing material.

Use an auxiliary fence in contact with the

table top when ripping workpieces less than

2 mm thick. A thin workpiece may wedge

under the rip fence and create a kickback.

Kickback causes and related warnings

Kickback is a sudden reaction of the workpie-

ce due to a pinched, jammed saw blade or

misaligned line of cut in the workpiece with

respect to the saw blade or when a part of

the workpiece binds between the saw blade

and the rip fence or other xed object. Most

frequently during kickback, the workpiece

is lifted from the table by the rear portion of

the saw blade and is propelled towards the

operator. Kickback is the result of saw misuse

and/or incorrect operating procedures or

conditions and can be avoided by taking

proper precautions as given below.

Never stand directly in line with the saw bla-

de. Always position your body on the same

side of the saw blade as the fence. Kickback

may propel the workpiece at high velocity

towards anyone standing in front and in line

with the saw blade.

Never reach over or in back of the saw blade

to pull or to support the workpiece. Acciden-

tal contact with the saw blade may occur or

kickback may drag your ngers into the saw

blade.

Never hold and press the workpiece that is

being cut o against the rotating saw blade.

Pressing the workpiece being cut o against

the saw blade will create a binding condition

and kickback.

Align the fence to be parallel with the saw

blade. A misaligned fence will pinch the

workpiece against the saw blade and create

kickback.

Use a featherboard to guide the workpiece

against the table and fence when making

non-through cuts such as rabbeting. A fe-

atherboard helps to control the workpiece in

the event of a kickback.

Support large panels to minimise the risk

of saw blade pinching and kickback. Large

panels tend to sag under their own weight.

Support(s) must be placed under all portions

of the panel overhanging the table top.

Use extra caution when cutting a workpiece

that is twisted, knotted, warped or does not

have a straight edge to guide it with a mitre

gauge or along the fence. A warped, knotted,

or twisted workpiece is unstable and causes

misalignment of the kerf with the saw blade,

binding and kickback.

Never cut more than one workpiece, stacked

vertically or horizontally. The saw blade could

pick up one or more pieces and cause kick-

back.

When restarting the saw with the saw blade

in the workpiece, centre the saw blade in the

kerf so that the saw teeth are not engaged in

the material. If the saw blade binds, it may lift

up the workpiece and cause kickback when

the saw is restarted.

Keep saw blades clean, sharp, and with suf-

cient set. Never use warped saw blades or

saw blades with cracked or broken teeth.

Sharp and properly set saw blades minimise

binding, stalling and kickback.

Table saw operating procedure warnings

Turn o the table saw and disconnect the

power cord when removing the table insert,

changing the saw blade or making adjust-

ments to the riving knife or saw blade guard,

and when the machine is left unattended.

Precautionary measures will avoid accidents.

Never leave the table saw running unatten-

ded. Turn it o and don’t leave the tool until

it comes to a complete stop. An unattended

running saw is an uncontrolled hazard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Max 31131 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info