Bedienungsanleitung Max 32891 (Seite 55 von 161) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

789308

Zoom out

Zoom in

Vorherige Seite

1/161

Nächste Seite

• Usethepowertool,accessories,and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for

operations dierent from those intended

could result in a hazardous situation.

Service

• Haveyourpowertoolservicedbya

qualied repair person using only

identical replacement parts. This will

ensure that the safety of the power tool is

maintained.

Safety warnings for mitre saws

• Mitresawsareintendedtocutwoodor

wood-like products, they cannot be used

with abrasive cut-o wheels for cutting

ferrous material such as bars, rods, studs,

etc. Abrasive dust causes moving parts

such as the lower guard to jam. Sparks

from abrasive cutting will burn the lower

guard, the kerf insert and other plastic

parts.

• Useclampstosupporttheworkpiece

whenever possible. If supporting the

workpiece by hand, you must always

keep your hand at least 100 mm from

either side of the saw blade. Do not use

this saw to cut pieces that are too small

to be securely clamped or held by hand.

If your hand is placed too close to the

saw blade, there is an increased risk of

injury from blade contact.

• Theworkpiecemustbestationaryand

clamped or held against both the fence

and the table. Do not feed the workpiece

into the blade or cut “freehand” in any

way. Unrestrained or moving workpieces

could be thrown at high speeds, causing

injury.

• Pushthesawthroughtheworkpiece.Do

not pull the saw through the workpiece.

To make a cut, raise the saw head and

pull it out over the workpiece without

cutting, start the motor, press the saw

head down and push the saw through

the workpiece. Cutting on the pull stroke

is likely to cause the saw blade to climb

on top of the workpiece and violently

throw the blade assembly towards the

operator.

• Nevercrossyourhandovertheintended

line of cutting either in front or behind

the saw blade. Supporting the workpiece

“cross handed” i.e. holding the workpiece

to the right of the saw blade with your

left hand or vice versa is very dangerous.

• Donotreachbehindthefencewith

either hand closer than 100 mm from

either side of the saw blade, to remove

wood scraps, or for any other reason

while the blade is spinning. The proximity

of the spinning saw blade to your hand

may not be obvious and you may be

seriously injured.

• Inspectyourworkpiecebeforecutting.

If the workpiece is bowed or warped,

clamp it with the outside bowed face

toward the fence. Always make certain

that there is no gap between the

workpiece, fence and table along the line

of the cut. Bent or warped workpieces

can twist or shift and may cause binding

on the spinning saw blade while cutting.

There should be no nails or foreign

objects in the workpiece.

• Donotusethesawuntilthetableis

clear of all tools, wood scraps, etc.,

except for the workpiece. Small debris

or loose pieces of wood or other objects

that contact the revolving blade can be

thrown with high speed.

• Cutonlyoneworkpieceatatime.

Stacked multiple workpieces cannot be

adequately clamped or braced and may

bind on the blade or shift during cutting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Max 32891 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info