Bedienungsanleitung Max 32891 (Seite 56 von 161) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

789308

Zoom out

Zoom in

Vorherige Seite

1/161

Nächste Seite

• Ensurethemitresawismountedor

placed on a level, rm work surface

before use. A level and rm work

surface reduces the risk of the mitre saw

becoming unstable.

• Planyourwork.Everytimeyouchange

the bevel or mitre angle setting, make

sure the adjustable fence is set correctly

to support the workpiece and will not

interfere with the blade or the guarding

system. Without turning the tool “ON”

and with no workpiece on the table,

move the saw blade through a complete

simulated cut to assure there will be no

interference or danger of cutting the

fence.

• Provideadequatesupportsuchas

table extensions, saw horses, etc. for a

workpiece that is wider or longer than

the table top. Workpieces longer or wider

than the mitre saw table can tip if not

securely supported. If the cut-o piece or

workpiece tips, it can lift the lower guard

or be thrown by the spinning blade.

• Donotuseanotherpersonasa

substitute for a table extension or as

additional support. Unstable support for

the workpiece can cause the blade to

bind or the workpiece to shift during the

cutting operation pulling you and the

helper into the spinning blade.

• Thecut-opiecemustnotbejammed

or pressed by any means against the

spinning saw blade. If conned, i.e. using

length stops, the cut-o piece could get

wedged against the blade and thrown

violently.

• Alwaysuseaclamporaxturedesigned

to properly support round material such

as rods or tubing. Rods have a tendency

to roll while being cut, causing the blade

to “bite” and pull the work with your hand

into the blade.

• Letthebladereachfullspeedbefore

contacting the workpiece. This will

reduce the risk of the workpiece being

thrown.

• Iftheworkpieceorbladebecomes

jammed, turn the mitre saw o. Wait for

all moving parts to stop and disconnect

the plug from the power source and/

or remove the battery pack. Then work

to free the jammed material. Continued

sawing with a jammed workpiece could

cause loss of control or damage to the

mitre saw.

• Afternishingthecut,releasetheswitch,

hold the saw head down and wait for the

blade to stop before removing the cut-o

piece. Reaching with your hand near the

coasting blade is dangerous.

• Holdthehandlermlywhenmakingan

incomplete cut or when releasing the

switch before the saw head is completely

in the down position. The braking action

of the saw may cause the saw head to be

suddenly pulled downward, causing a

risk of injury.

• Donotletgoofthehandleoncethesaw

head has reached the lowest position.

Always guide the saw head back to the

top position by hand. There is a risk

of injury if the saw head moves in an

uncontrolled manner.

• Keepyourworkareaclean.Material

mixtures are particularly hazardous. Light

metal dust may catch re or explode.

• Donotusedull,cracked,bentor

damaged saw blades. Unsharpened

or improperly set saw blades produce

narrow kerf causing excessive friction,

blade binding and kickback.

• Donotusesawbladesmadefromhigh

speed steel (HSS). Such saw blades can

easily break.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Max 32891 Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info