Air flow direction adjustment procedureThis type has no this function
Up/down direction can be adjusted by using the AIRFLOW button on the remote controller.
This button,each time pressed,changes the mode in the following sequence:
Up/down direction can be adjusted by using the AIRFLOW button on the remote controller.
This button,each time pressed,changes the mode in the following sequence:
Adjusting air flow direction
NOTE
When the room temperature controller(thermostat)trips in the heating mode or when the defrosting operation is conducted,the blow flap changes automatically to theWhen the room temperature controller(thermostat)trips in the heating mode or when the defrosting operation is conducted,the blow flap changes automatically to the
horizontal position.horizontal position.
When the heating operation has just started and the room temperature is still low,it may take a little time before the flap moves to the above sway operation angle.When the heating operation has just started and the room temperature is still low,it may take a little time before the flap moves to the above sway operation angle.
The flap may stop at the tilted down-blow position during the"Sway operation"in the heating mode,The flap may stop at the tilted down-blow position during the"Sway operation"in the heating mode,
AUTO
push the LOUVER button,changes the mode to swing louver.
Push the button,to stop swing.
push the LOUVER button,changes the mode to swing louver.
Push the button,to stop swing.
About TIMER operation
About Amenity reservation
Amenity reservation funcition is provided to start the operation a little earlierAmenity reservation funcition is provided to start the operation a little earlier
so that the room temperature is near the optimum temperature at the timer ONso that the room temperature is near the optimum temperature at the timer ON
time in case of starting the operation by TIMER ON/OFF.time in case of starting the operation by TIMER ON/OFF.
MechanismMechanism
Checking of the room temperatureChecking of the room temperature
starts 60 minutes ahead of the timerstarts 60 minutes ahead of the timer
ON time.Depeding on the tempera-ON time.Depeding on the tempera-
ture at that time,operation starts 5 to ture at that time,operation starts 5 to
60 minutes ahead of the timer ON time.60 minutes ahead of the timer ON time.
Amenity reseration is the functionAmenity reseration is the function
only for COOLand HEAT operationonly for COOLand HEAT operation
mode(including AUTO).It does notmode(including AUTO).It does not
actuate in DRY mode.actuate in DRY mode.
About SLEEP OperationAbout SLEEP Operation
When the SLEEP operation is selected,the room temperature is auto-
matically controlled with elapsed time so that the room isn't too cool
during cooling or too warm during heating.
During cooling and dry:Present temperature is raised 1 in an hour
(when the timer is set),and 2 raise in two hours.Then the temperature
dosen't change ever.
During heating:Present temperature is lowered 1 in an hour (when the
timer is set),and 2 lower in two hours.Then the temperature dosen't
change ever.
In cool operation In cool operation
Set
Temperature
Set
Temperature
Check the room
temp. 60 min
ahead
Check the room
temp. 60 min
ahead
Set timeSet time
(Operation)(Operation)
(Stop) Operation starts(Stop) Operation starts
8
indoor unit
refrigerantflow direction
3-way valve
(6). If the uint has no leakage,then Tighten the
exhaust nut of 3-way valve.
(8)Back the exhaust nut to the uint..
(3).Loose the outlet nut of the additional freon refrigerant pot .
(1).Loosen the liquid pipe flare nut and remove the
exhaust nut of 3-way valve.
(2). Connect the outlet nut of the additional freon refrigerant
pot to the exhaust mouth .
(9).Loosen the valve spindle and core to Maximum.
(7).Press the spindle and let the additional freon
refrigerant leak out until the velocity of purging Air
is slow and warm .
3-way valve diagram
Connect to indoor unit
Close position
Valve spindle
Exhaust nut
Valve core
Connect to outdoor unit
Air exhaust process:
Connect hose
additional freon refrigerant pot
outlet nut
Refrigerant Volume to Be Added
Refrigerant volume to be added is calculated according to outdoor unit installation manual.
Be sure to add refrigerant measuring by a scale.
If the added refrigerant volume is inadequate (too much or insufficient), the compressor
malfunction will be caused. Be sure to calculate the refrigerant volume carefully.
The service man should write down the piping length and the added refrigerant volume
in the nameplate, which is on the electric control box cover of outdoor unit, for
diagnosing the compressor and refrigeration circulation malfunction.
CAUTION
The refrigerant refrigerant charge volume for the unit is based on using a 5m connecting
pipe. If the connecting pipe's length is longer than 5m, it is advisable to charge
additional refrigerant for the unit in order to achieve better operation.
21
Exhaust mouth
Exhaust spindle
(4).After exhausting air for almost one miniute,then
tighten the liquid pipe flare nut
Charge additional refrigerant
(5). Detect all the pipe joints leakage of freon in this
unit with soap water.
About FAN SPEED
Capacity of the air conditioner can be selected by your choice.During heating or cooling.Capacity of the air conditioner can be selected by your choice.During heating or cooling.
Operation capacity by your choice Operation capacity by your choice
Set automatically by microcomputer Set automatically by microcomputer
Powerful operation with high capaciy Powerful operation with high capaciy
Standard operation Standard operation
FAN SPEEDFAN SPEED
AUTOAUTO
HIHI
MEDMED
Energy-saving operation
Lo
About power-off memory function
When the air conditioner disconnect the power suddenly, restart it, the air conditioner operates at the mode
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Maxicool CTL50H4A wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
