Bedienungsanleitung Maxxmee BG-E-0220 - 08827 (Seite 13 von 32) (Deutsch, Englisch, Holländisch, Französisch)

769817

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Decorative Fireplace EN

4. Carefully ﬁ ll the water tank with water

using a measuring cup or something

similar.

5. Place the splash guard on the water

tank and the cover on the main unit.

USE

Please Note!

■The device must have clearance of at

least 1 m above it and to all sides and

be placed on a dry, even, solid and

moisture-resistant surface. Do not po-

sition the device near to moisture-sen-

sitive objects and materials. Harmful

microorganisms may be produced on

damp materials, such as curtains or

such like.

■The water in the water tank needs

to be changed every two days and

the water tank needs to be cleaned

thoroughly in order to prevent the

formation of harmful microorganisms.

■Only connect the device to a plug

socket that is properly installed and

matches the technical data of the

device. The plug socket must also be

readily accessible after connection so

that the connection to the mains can

quickly be isolated.

■Only use the device when all halogen

lamps are inserted.

■Do not operate the device unsuper-

vised so that you can intervene imme-

diately if there are any faults.

1. Fill the water tank (7) (see the “Filling

the Water Tank” chapter).

2. Fully unwind the connecting cable

and connect it to a plug socket.

3. Move the toggle switch (6) into theI

position.

4. Press the On / Off button (4) to switch

on the device. The halogen lamps (11)

start to light up. After around a min-

ute the ultrasonic atomisers(1) start

to produce a water mist. The device

requires a little time to produce a real-

istic ﬂ ame pattern. The ﬂ ame pattern

will develop as the device is used and

become increasingly more vivid.

 To accelerate the ﬂ ame develop-

ment, warm water (approx. 40 °C

to 60 °C) can be used.

Please Note: If there is not enough

water in the water tank, the device

switches off automatically.

5. If the device is no longer going to

be used, press the On / Off button

to switch it off. The halogen lamps

go out and the ultrasonic atomisers

switch off.

6. Move the toggle switch to the O posi-

tion and pull the connecting cable out

of the plug socket.

 After use, there may still be water

remaining on the splash guard

and on the cover.

CLEANING AND STORAGE

Please Note!

■The water tank needs to be emptied

and cleaned every two days.

■Do not use any sharp or abrasive

cleaning agents or cleaning pads to

clean the device. They may damage

the surfaces.

• Make sure that the device is not con-

nected to the mains power.

• Wipe down the device with a soft,

damp cloth. Remove more stubborn

dirt with a little detergent.

• If necessary, clean the diaphragms

of the ultrasonic atomisers (1) with a

cotton bud soaked in alcohol.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Maxxmee BG-E-0220 - 08827 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Maxxmee BG-E-0220 - 08827

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info