Bedienungsanleitung McCulloch CABRIO 246-25CC (Seite 11 von 12) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

590545

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

DANGER. Do not run engine without shaft

attached as clutch could fly off.

1) Insert the shaft (A) into the engine joint (B)

making the female squared end (C) inside the

joint mates with the male squared end (D) of

the shaft.

Rotate the shaft from right to left to obtain a

precise fit. Now tighten the locking bolt (E)

clockwise to ensure the shaft is held firmly in

the joint.

2) If the joint is not tightened onto the engine

housing, first make sure the shaft is fully and

correctly engaged up to the shank, then tighten

the 4 screws (A) in a criss-cross sequence.

3) Assemble the eyelet (A) of the ground wire

onto the end of the throttle cable and install the

washer (B).

Insert the throttle cable into the cable mount

(C), install the second washer (B) and insert the

hexagonal nut.

4) Fit the end of the trigger cable connector (B)

into the slot on swivel (C).

Adjust the nut (D) of the trigger cable connector

so that the cable can easily slide in the opening

with a play of 1 mm before operating the swivel (C).

Tighten now the hexagonal nut (E).

6) Stop switch (STOP) cable: fit the connection.

G. ENGINE/SHAFT ASSEMBLY

J FRONT HANDLE

Secure the handle in front of the label placed on

the shaft 11 cm from the rear grip when

assembling nylon string head and 36 cm when

assembling metallic blades. This position ensures

optimum balance and safety. The handle must be

perpendicular to the shaft as illustrated.

H. HANDLE ASSEMBLY

I. STARTING AND STOPPING THE ENGINE

WARNING. First read sections: SAFETY RULES,

SAFETY USAGE and SYMBOLS.

COLD ENGINE STARTING

1) Move stop switch to the “ON” position.

2) Depress the safety lever (S), squeeze the

accelerator trigger (A) and push the throttle

advance forwards (B). Now release the

accelerator trigger (A) and then the throttle

advance (B).

WARNING: when the throttle advance is

engaged, the head or blade rotates.

Move choke lever (E) to the closed position .

4) Press the primer bulb (C) several times until

you see fuel going back to carburetor through

pipe (D). Pull starter rope until engine fires once.

5) Move choke lever (E) to the open position

then pull starter rope until engine fires. Let

engine run for a few seconds holding the

trimmer. Now disengage throttle advance by

pulling trigger completely. Engine will now keep

on running at idle speed.

HOT ENGINE STARTING

STOP switch on START position I. Trigger on

idle position (released).

Choke towards (open position ). Press the

primer bulb (C) several times until you see fuel

going back to carburetor through pipe (D). Pull

starter rope.

WARNING: when the throttle (B) advance is

engaged, the head or blade rotates.

6) ENGINE STOPPING

Press the stop switch moving it to STOP

position 0.

WARNING: when the engine is switched off

rotating parts, blade or nylon string head, will

keep on rotating for a few seconds. Hold the

machine until all parts come to a standstill.

N.B. In an emergency the above mentioned

delay in stopping may be shortened by

touching blade parallel on the ground.

L. CARBURETTOR ADJUSTMENT

Your machine may be fitted with a highly

sensitive low emission carburettor. We now

therefore recommend that carburettor

adjustments are only made by an authorised

servicing dealer, equipped with instruments

that will ensure best performance with lowest

emission levels.

To adjust the idle speed, however, proceed as

follows:

With engine running and warm, slowly turn screw

‘I’ or ‘T’ clockwise until the engine runs smoothly

with a consistent noise level but without making

the chain or cutting head rotate.

If the cutting attachment does move or the engine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch CABRIO 246-25CC Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info