Bedienungsanleitung McCulloch CABRIO 246-25CC (Seite 12 von 12) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

590545

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

From time to time ensure all screws are tight.

Replace damaged, worn, cracked or warped

blades. Always make sure nylon string head or

blade have been assembled correctly (see

sections NYLON STRING HEAD and BLADE

ASSEMBLY) and blade fastener is tightened.

1) AIR FILTER CLEANING

(at least every 25 working hours).

A dust clogged air filter may cause carburetor

problems.

This may prevent the engine from reaching its

maximum speed and cause high fuel

consumption and/or difficult starting.

Remove filter cover as shown in figure 1.

Carefully clean the inside of filter box. The filter

can also be cleaned with compressed air.

2) SPARK PLUG

From time to time (at least every 50 hours)

remove and clean the spark plug and check

the electrode gap (0,5/0,6 mm.). Replace

spark plug about every 100 working hours or

whenever it is extremely encrusted. Heavily

encrusted electrodes can result from an

incorrect carburetor setting or from wrong fuel

mixture (too much oil in the petrol) or a poor

quality of oil in the fuel mix. Check and correct.

3) FUEL FILTER

To change fuel filter remove the tank cap and

pull out the filter with a piece of bent wire or

long forceps. Contact your Service Station for

general servicing and cleaning of internal parts

at least once a year.This will reduce the

possibility of unexpected problems and will

ensure maximum product life and efficiency.

REGULARLY: it is important, in order to avoid

engine overheating, to remove dust and dirt

from slots, gaps and from in between cylinder

fins using a wooden scraper.

LONG STORAGE: empty fuel tank and run

engine until dry.

Store trimmer in a dry place.

M. REGULAR MAINTENANCE

FAULT FINDING TABLE

Engine will

Engine runs badly The machine

not start

or looses power runs but does

when cutting not cut well

•

••

•

Engine still gives trouble: contact your dealer.

Check STOP switch is in the position I.

Control fuel level min. 25%tank capacity.

Check air filter is clean.

Remove spark plug, dry it, clean it and

adjust it, and replace it, if necessary.

Control and adjust the carburetor screws

if necessary.

Change fuel filter. Contact your dealer.

Carefully follow the cutting accessory

assembly instructions.

Check metal cutting accessory is sharp.

Otherwise, contact your dealer.

runs too fast, slowly turn screw ‘I’ or ‘T’ in an

anticlockwise direction until the correct speed is

obtained.

Precise numerical engine speed settings are

mentioned in the technical detail chart in the front

of the owner’s manual.

NOTE:

Direct drive trimmers: The cutting head will

always rotate when engine is running.

B) All the above mentioned adjustments must be

made with the relevant cutting attachment

correctly fitted.

Warranty may be invalidated from incorrect

carburettor adjustment made by persons other

than an authorised dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch CABRIO 246-25CC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info