Bedienungsanleitung McCulloch CS42STE (Seite 8 von 532) (Alle Sprachen)

684234

Zoom out

Zoom in

Vorherige Seite

1/532

Nächste Seite

FUEL HANDLING

FUELING ENGINE

a WARNING: Remove fuel cap slowly when

refueling.

IMPORTANT: This equipment is designed to operate

RQXQOHDGHGSHWUROZLWKDPLQLPXPRFWDQH520

with ethanol blended up to 10% maximum by volume

(%HIRUHRSHUDWLRQSHWUROPXVWEHPL[HGZLWK

a good quality synthetic 2-cycle air-cooled engine oil

designed to be mixed at a ratio of 50:1.

DO NOT USE automotive oil or marine oil. These oils

will cause engine damage. When mixing fuel, follow

instructions printed on container. Once oil is added to

petrol, shake container momentarily to assure that the

fuel is thoroughly mixed. Always read and follow the

safety rules relating to fuel before fueling your unit.

Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

CAUTION: Never use straight petrol in your unit.

This will cause permanent engine damage and void

the limited warranty. Do not use alternate fuels such

as ethanol blends above 10% by volume (E-15,

(RUDQ\PHWKDQROEOHQGHGIXHO8VHRIWKHVH

fuels can cause major engine performance and

durability problems.

Petrol, litre Two-stroke oil, litre

5 0,10

10 0,20

15 0,30

20 0,40

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubrication.

Lubrication is provided by the automatic oiler system

ZKHQWKHRLOWDQNLVNHSW¿OOHG/DFNRIRLOZLOOTXLFNO\

ruin the bar and chain.

Too little oil will cause overheating shown by smoke

coming from the chain and/or discoloration of the

bar. In freezing weather oil will thicken, making it

necessary to thin bar and chain oil with a small

DPRXQWWRRI'LHVHO)XHORUNHURVHQH%DU

DQGFKDLQRLOPXVWEHIUHHÀRZLQJIRUWKHRLOV\VWHPWR

pump enough oil for adequate lubrication.

Bar and chain oil is recommended to protect your unit

against excessive wear from heat and friction. If bar

and chain oil is not available, use a good grade SAE

30 oil.

• Never use waste oil for bar and chain lubrication.

• Always stop the engine before removing the oil cap.

STARTING AND STOPPING

PRE-OPERATION INSPECTION

Perform the following steps before every use of the

machine:

• Check fuel mixture level

• Check bar lubrication

• Check chain sharpness

NOTE: Chain sharpening is a complicated task

that requires special tools. We recommend that

you refer chain sharpening to a professional chain

sharpener.

• Check chain tension

• Inspect and clean the guide bar

• Check for damaged parts

• Check for loose caps

• Check for loose fasteners

• Check for loose parts

• Check for fuel and oil leaks

NOTE: It is normal for a small amount of oil to

appear under the saw after the engine stops. Do not

confuse this with a leaking oil tank.

STARTING POSITION

1. /D\WKHFKDLQVDZRQDÀDWVXUIDFH7KHFXWWLQJ

attachment must not be in contact with the

ground. Make sure the chain is free to turn without

contacting any object.

2. Lock the chain brake by pushing forward on the

handguard.

3. Place your left hand on the handlebar and your

right hand on the starter rope. Push your right foot

into the rear handle to stabilize the chainsaw.

4. Follow the starting instructions.

888

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch CS42STE Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info