Bedienungsanleitung McCulloch CS42STE (Seite 9 von 532) (Alle Sprachen)

684234

Zoom out

Zoom in

Vorherige Seite

1/532

Nächste Seite

STARTING A COLD ENGINE

Follow these instructions to start your chainsaw. Your

chainsaw has a starting reminder decal similar to the

one shown below:

Make sure the chain brake is locked

before starting.

Press the primer (air purge) bulb

10 times. If fuel is not seen, press

the primer (air purge) bulb 10 more

times.

Note: If the outdoor temperature

is less than 4°C (40°F), press 15

times.

Unlock, then move the blue start

lever to the top (START) position.

Using your right hand, pull the

starter rope sharply until the

machine starts, or a maximum of

6 times.

Note: If the machine does not start

after 6 pulls, repeat the procedure

for starting a cold engine.

IMPORTANT: When pulling the starter rope, do not

use the full extent of the rope as this can cause the

rope to break. Do not let starter rope snap back. Hold

the handle and let the rope rewind slowly.

Allow the engine to run for 30

seconds.

Before accelerating to full throttle,

pull the front hand guard towards

the front handle. The chain brake is

now unlocked.

Squeeze the throttle trigger for 10 seconds, then

release the throttle trigger to set normal idle. Your

chainsaw is now ready for use.

a WARNING: The chain must not move when the

engine runs at idle speed. If the chain moves

at idle speed refer to the MAINTENANCE

section for carburettor adjustment.

a WARNING: Avoid contact with the mufer. A

hot mufer can cause serious burns.

a WARNING: Do not attempt to throw or drop-

start the chain saw. Doing so will put the

operator at risk of serious injury due to loss of

control of the chain saw.

STARTING A WARM ENGINE

Make sure the chain brake is locked

before starting.

Press the primer (air purge) bulb

10 times.

Move the blue start lever to the top

(START) position.

Move the blue start lever to the

bottom (RUN) position.

Using your right hand, pull the

starter rope sharply until the

machine starts, or a maximum of

6 times.

Before accelerating to full throttle,

pull the front hand guard towards

the front handle. The chain brake is

now unlocked.

Squeeze the throttle trigger for 10 seconds, then

release the throttle trigger to set normal idle. Your

chainsaw is now ready for use.

DIFFICULT STARTING

(or starting a ooded engine)

NOTE: If the product does not start, the fuel can be

too hot.

NOTE: Always use new fuel and decrease the

operation time during warm weather.

1. Put the product in a cool area away from open

sunlight.

2. Let the product cool down for 20 minutes at

minimum.

3. Press the primer bulb again and again for 10-15

seconds.

4. Obey the procedure to start a cold engine.

STOPPING

To stop the engine push the STOP switch down.

a WARNING! To avoid involuntary start up,

the spark plug cap must always be removed

from the spark plug when the machine is

unsupervised.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch CS42STE Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info