Bedienungsanleitung McCulloch M3616 (Seite 10 von 17) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch)

478395

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

completely (to the OFF CHOKE position)

and then f ollowing t he warm engine starting

procedure listed above. Ensure the ON/

STOP switch is in the ON position. Starting

could require pulling the starter rope handle

many times dependingon how badly theunit

is flooded. If engine fails to start, refer to the

TROUBLESHOOTING TABLE.

CHAIN BRAKE

WARNING: If the brake band is worn

too thin it may break when the chain brake is

triggered. With a broken brake band, t he chain

brake will not stop the chain. The chain brake

should be replaced by an authorized service

dealer if any part is worn to less than 0,5 mm

thick. Repairs on a chain brake should be

made by an authorized service dealer . Take

your unit t o t he pl ace of purchase if purchased

from a servicing dealer,or to the nearest autho-

rized master service dealer.

S This saw is equipped with a chain brake.

The brake is designed to stop the chain if

kickback occurs.

S The inertia activated chain brake is activated

if t he f ront hand guard is pushed forward, ei-

ther manually or by centrifugal force.

S If the brake is already ac tivated, it is disen-

gaged by pulling thefront hand gu ard back

toward the fro nt handle as far as possible.

S When cutting with the saw,the chainbrake

must be disengaged.

Disengaged

Engaged

Braking function control

CAUTION:

The chain brake must be

checked several times daily. The engine

must berunningw henperformingthis proce-

dure. This is theonly i n stance when thesaw

should be placed on t he ground with th e en-

gine running.

Place the saw on f irm ground. Grip the rear

handlewithyourrighthand andthefronthan-

dle with your left hand. Apply full throttle by

fully depressing the t hrottle trigger. Activate

the chain brake by turning your left wrist

against the hand guard without releasing

your grip around the front handle. The chain

should stop immediately .

Inertia activating function c ontrol

WARNING: When performing the fol-

lowing procedure, the engine must be turned

off.

Grip therear handle with your righ t hand and

the f ront handle with your left hand. H old the

chain saw approximately 35 cm above a

stump or other wooden surface. Release

your grip on the front handle and use the

weight of the saw to let the top of the guide

bar fall forward and contact the stump.

When the tip of the bar hits the stump, the

brake should activate.

CUTTING METHODS

IMPORTANT POINTS

S Check chain tension b efore first use and a f-

ter 1 minute of operation. See CHAIN TEN-

SION in the ASSEMBLY section.

S Cut wood only . Do not cut metal, plastics,

masonry , no n-wood buil ding m ateria ls, etc.

S The bumper spike may be used as a pivot

when making a cut.

S Stop the saw if the chain strikes a f oreign ob-

ject. I nspect the saw and repair parts as nec-

essary.

S Keepthechain outof dirtandsand. Evena

small amount of d irt willquickly dull achain

and increase the possibility of kickback.

S Practice cutting a few small logs using the

following techniques to get the “feel” of us-

ing your saw before you begin a major

sawing operation.

S Squeeze the throttle trigger and allow t he

engine to reach full speed before cutting.

S Begin cutting with the saw frame

against the log.

S Keep the engine at full speed the entire

time you are cutting.

S Allowthechain tocutfory ou.Exertonly

light downward pressure.

S Release the throttle trigger as soon as

the cut is completed, allowing the en-

gine to idle. If you run the saw at full

throttle without a cutting load,unneces-

sary wear can occur.

S To avoidlosingcontrolwhencutiscom-

plete,donotputpr essure onsaw atend

of cut.

S Stop the engine before settingt he saw down.

TREE FELL ING TECHNIQUES

WARNING: Felling a tree requires

chain saw skills and experience. Inexperi-

enced us ers should not fellt rees. Do not at-

tempt any task that makes you feel uncom-

fortable or unsure.

WARNING:Do notcut nearbuildings

or electrical wires if you do not know the di-

rection of tree fall, at night s ince y ou w ill not

be able to see well, or during bad weather

such as rain, snow, or strong winds. as fall is

unpredictable.

Carefully plan your sawing operation in ad-

vance. You need a clear area all around the

tree so you c an have secure footing. Check

for broken or dead branches which can fall

on you causing serious injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

McCulloch M3616 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info