Bedienungsanleitung MCZ ALEA AIR 7 XUP S1 (Seite 12 von 36) (Englisch)

812523

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

13-MENU ENTRIES AND OPERATION

h - Pellet Recipe

This function is for adapting the stove to the type of pellet in use. As there are many types of pellets available on the market, operation

of the stove can vary considerably according to the quality of the fuel. When the pellets clog up the brazier due to excess loading of fuel

or when the ame is always high even at low power, or when the ame is low, it is possible to decrease/increase the amount of pellets

in the brazier:

The available values are:

-3 = A decrease of 20% with respect to the factory setting.

-2 = A decrease of 13% with respect to the factory setting.

-1 = A decrease of 6% with respect to the factory setting.

0% No changes.

3 = An increase of 10% with respect to the factory setting.

2 = An increase of 6% with respect to the factory setting.

1 = An increase of 3% with respect to the factory setting.

Proceed as follows to edit the recipe:

• Press the “menu” key.

• Use the arrow keys to scroll through and select “Settings”

• Press “menu” to conrm.

• Scroll with the arrows and select “Pellet recipe’’.

• Press “menu” to conrm.

• Edit the % by using the + - keys.

• Press ‘’menu’’ to conrm and ‘’esc’’ to exit

i - Smoke rpm % variation

In the event the installation presents problems in extracting smoke (lack of draught or even pressure in the duct), it is possible to increase

the smoke and ash extraction speed. This change resolves all potential problems related to pellets clogged in the brazier and deposits

forming at the bottom of the brazier itself caused by poor quality fuel or fuel that produces a lot of ash. The values available range from

-30% to +50%, with increments of 10 percent at a time. Negative variation may be required if the ame is too low.

To edit this parameter, proceed as follows:

• Press the “menu” key.

• Use the arrow keys to scroll through and select “Settings”

• Press “menu” to conrm.

• Scroll with the arrows and select “Fume rpm Var.”.

• Press “menu” to conrm.

• Edit the % by using the + - keys.

• Press ‘’menu’’ to conrm and ‘’esc’’ to exit

j - Components test

This can only be done when the stove is o and allows you to select the components to be tested:

• Glow plug: it is turned on for a xed period of 1 minute during which the panel displays the countdown in seconds.

• Feed screw: it is powered for a xed period of 1 minute during which the panel displays the countdown in seconds.

• Extractor: it is activated at 2500 rpm for a xed period of 1 minute during which the panel displays the countdown in seconds.

• Heat exchanger: enables you to conduct the test in V5 for a xed period of 1 minute during which the panel displays the countdown

in seconds.

Proceed as follows to enable the “Components test” function (only with stove o):

• Press the “menu” key.

• Use the arrow keys to scroll through and select “Settings”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MCZ ALEA AIR 7 XUP S1 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MCZ ALEA AIR 7 XUP S1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info