Bedienungsanleitung MCZ Vivo 70 Wood (Seite 35 von 42) (Englisch)

643528

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Chapter 6

INSTALLATION AND USE MANUAL

page 35

6.2.1. Phases for first test lighting

 Make sure you have read and completely understood the

contents of this instruction booklet.

 Remove any components which might burn from the fireplace

stove and door (Packaging, various instructions and adhesive

labels).

 Remove the stickers from the ceramic glass or the high

temperature could melt them and irreparably damage the glass.

In this case, the MCZ warranty does not cover the glass.

 Completely open the front register of the combustion air. (turn

the lever all the way to the left)

 Place wood in small pieces that is well dried (humidity 15/20%).

Light the fire at low power without excessively heating the

structure. It is normal that odours from manufacturing residue

will form the first time lighting occurs, and will disappear after a

lighting at full power has occurred a few times.

6.3. CHOICE OF FUEL

To obtain the maximum performance from your VIVO fireplace stove, it

is of primary importance to use wood with suitable characteristics.

It is advisable to use wood for heating such as oak, beech, locust

tree, or oak with good calorific energy, or logs of pressed wood that

do not have resin. These have a high calorific power and must

be used with caution to avoid overheating which could damage

the stove.

It is advisable to use fuels such as poplar, pine, lime tree, or

chestnut which have low calorific power, since they are soft wood and

also they do not burn for a long time.

Avoid using fuels such as pine, fir, and olive as they contain a high

degree of resin and their combustion may substantially soil the fire

mouth and the ceramic glass; also, they do not have an exceptional

yield.

For all types of wood listed, the humidity they contain is

essential because it determines the calorific energy.

Do not use treated fuels (such as painted or

varnished wood, or particle board) or unsuitable

materials (such as plastics and derivatives), which

could release toxic or polluting substances. Do not

burn rubbish.

The gases produced by combustion due the use of

unsuitable fuels cause damage to the fireplace stove

and the chimney, they cause pollution and can

compromise your health.

A high percentage of humidity produces condensation in the

smoke duct causing an alteration in the draught and

generating smoke and a significant deposit of soot on the

glass of the door and in the flue pipe with a possible risk of

a chimney fire later on.

Wood drying

time (i.e. beech)

humidity

Heat

power

Kcal/h

Freshly cut 50 /

3 months 40 2410

6 months 35 2700

9 months 30 2900

12 months 25 3150

15 months 20 3400

18 months 15 3710

21 months 10 3980

Figure 13 – Calorific energy (e.g. beech) in

relation to humidity contained.

Figure 12 – Maximum adjustment of

combustion air opening

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MCZ Vivo 70 Wood Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info