Bedienungsanleitung ME VD 603 (Seite 16 von 40) (Deutsch, Englisch, Holländisch, Französisch)

568582

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

VISTUS-VD | ENGLISH

enough hold then drill more holes and use them to also screw the

indoor station in place.

3. Drill the attachment holes with a 6 mm drill and insert one dowel in

each hole.

4. Feed the lines through the feed hole in the lower casing part

designed for this purpose and screw this down.

5. Attach the lines in accordance with the wiring plan and replace the

front casing section onto the lower casing section. Make sure that it

clicks correctly into place.

CONNECTION

An exact description of where the individual connections and terminals

are located can be found in the ﬁgures. The recommended wiring can be

seen in the corresponding wiring plan in the afﬁx.

Connect the lines to the audio, +15V, GND and video on the outdoor

station. These terminals are also present on the indoor stations and need

to be connected to one another 1:1.

Note on the 2-family versions: One four-pole connection terminal is

present in each residential unit. The connection terminals are numbered.

Connection terminal 1 is for the lower and connection terminal 2 is for

the upper bell button.

Connecting the door opener

The door opener is connected directly to the outdoor station with two

lines (Figure A ‚Door opener‘). No additional power supply is necessary

in order to control the door opener. The door opener must be designed

for 12 volt DC voltage and may not require more than 1A of power. In

the event that the door opener needs to be correctly polarised then both

connection terminals must be marked ‘lock +’ and ‘lock –‘.

Note: In order to prevent a door opening by tampering of the outdoor

station, we recommend the installation of the separately available

security door opener module SDO-10, which is mounted in the service

entrance box. The SDO-10 is also suitable for motor locking systems and

offers several adjustable door opening times and an

auto-door-open function.

Connecting the power supply

The power supply can be connected to either the indoor or the outdoor

station. Separate spring clips are present for this purpose.

It is also possible to connect the power supply directly to the signal line

e.g. from the fuse box to the outdoor and indoor units. The power supply

unit then needs to be connection with the ground (GND) and +15V.

Open power supply unit can supply up to 8 units with power.

Connecting the external camera

An external camera can be connected to the spring clips (Figure A ‚ext

Cam‘), for example in order to be able to monitor an additional area

that is not visible on the main camera. All cameras can be connected

that require a supply voltage of 12 Volt DC and supply

an FBAS video signal.

The video line is connected to the terminal (V2) and the ground line

is connected to the terminal (GND); the supply voltage for the camera

is taken from the terminals ‘VCC2’ (positive terminal) and ‘GND’

(negative terminal).

The external camera automatically receives ID 4 (see chapter on the ID

code). When the external camera is active it is not possible to transmit

sound. The X-module on the VDV 500 XCam is not required.

Connecting a ﬂoor button

Any ﬂoor button that is present (normal closing contact) is connected

to the terminals ‘ﬂoor button’ on the indoor unit. Alternative the button

can also be connected in parallel to the lines ‘audio’ and ‘GND’. On

the two-family version please note that the correct audio line is used

(Audio1 and GND for fam. 1 and Audio2 and GND for fam. 2).

Note: If a ﬂoor button is connected then an unchangeable ring tone

is played when the ﬂoor button is activated. This ring tone is ﬁxed

and is not included in the ‘normal’ tones/melodies to make it easy to

differentiate.

Connecting the wireless expansion model VTX-BELL

The VTX-BELL can be used to send the bell signal wirelessly to the

receiver in the BELL series (currently BELL 200 RX, BELL 210 USB and

BELL 220 RX). The wireless module will be attached to the 3-pole plug

inside the indoor station (Figures B+C). For more information please

see the VTX-BELL instructions.

POSSIBLE SETTINGS ON THE OUTDOOR STATION

The outdoor station has the following possibilities of adjusting the

system to your personal circumstances:

Volume on the outdoor station

The potentiometer (Figure A ‚Volume / Lautstärke‘) is used to set

the speaking volume on the outdoor station. For full volume turn the

potentiometer carefully in a clockwise connection until it stops and turn

it back a little. Turning the potentiometer in an anti-clockwise direction

reduces the volume.

ID code

If several outdoor stations are used in parallel (e.g. on the gate and

on the house), the DIP switch is used to set the ID code (Figure A,

VISTUS VD-600_I-Manual_210x240_Fin9.indd 16 10.06.13 15:52

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ME VD 603 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info