Bedienungsanleitung ME VD 603 (Seite 17 von 40) (Deutsch, Englisch, Holländisch, Französisch)

568582

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH | VISTUS-VD

1717

‚ID-CODE‘). This makes it possible to activate the individual outdoor

stations in turn from one indoor unit in order to be able to monitor the

scope of the corresponding outdoor units. The switch is activated on the

indoor station with the ‘monitor’ button.

ID1 = Switch 1 ‘on’, Switch 2 ‘on’

ID2 = Switch 1 ‘on’, Switch 2 ‘off’

ID3 = Switch 1 ‘off’, Switch 2 ‘on’

Note: ID 4 is not available for the outdoor station. It is reserved for the

outdoor camera. If several outdoor stations are used in parallel then

only one outdoor station can be connected to the external camera.

Door opener time

The DIP switch (Figure A, ‚Door opener time‘) is used to set how long

the door opener should be activated for. The possible settings are 1

second or 5 seconds. 5 seconds is the factory setting and works for

most standard door openers.

Switch ‘off’ corresponds to an opening time of 1 second.

Switch ‘on’ corresponds to an opening time of 5 seconds.

POSSIBLE SETTINGS ON THE INDOOR STATION

The following settings are possible on the indoor station to adjust the

system to your personal circumstances:

Ring tone volume (3.5“ and 7“ monitor)

The potentiometer (Figure B and C ‘Bell Volume‘’) is used to set the

ring/volume on the indoor station. For full volume turn the potenti-

ometer carefully in a clockwise connection until it stops. Turning the

potentiometer in an anti-clockwise direction reduces the volume.

Deactivate ring tone/melody (e.g. during the night)

The ring tone/melody can be deactivated, e.g. in order to prevent

disturbance during the night. Either press the mute button on the

indoor unit once brieﬂy. The LED below the mute button lights up red

as a reminder that the melody is deactivated. To activate the melody

again press the mute button again brieﬂy. When the red LED goes out

the melody has been re-activated.

The optical signal (surround light on the talk and door opener button)

remains active, even then the ring tone/melody is deactivated and still

rings. The red LED ﬂashes if the bell is rung while the mute is activated.

NOTE: If the VTX-BELL module is used then this will also be deactivated

in the silent mode, i.e. the connected receivers will not give a

signal either.

IMPORTANT: The monitor on the indoor station needs to be

activated for the following settings (e.g. by pressing the screen button).

Otherwise it is not possible to set the talk/volume, brightness, contrast,

colour saturation and melody.

Speaking volume (3.5“ and 7“ monitor)

The two side buttons (B/C. 12 and 13) can be used to set the speaking

volume in several steps. Button 12 is used to increase the volume and

button 13 to reduce it.

Brightness (3.5“ monitor)

The

button (B.8) is used to set the brightness on the monitor. The

button is pressed multiple times to increase the brightness. Once the

highest level of brightness has been reached another press will switch it

to the lowest level of brightness.

Contrast (3.5“ monitor)

The button (B.9) is used to set the contrast on the monitor. The

button is pressed multiple times to increase the contrast. Once the

highest level of contrast has been reached another press will switch it to

the lowest level of contrast.

Colour saturation (3.5“ Monitor)

The button (B.10) is used to set the colour saturation on the monitor.

The button is pressed multiple times to increase the saturation. Once

the highest level of saturation has been reached another press will

switch it to the lowest level of saturation.

Brightness (7“ monitor)

Press the button (C.8) on the indoor station once and the OSD will

display ‘Bright’. You can now increase the brightness using button (C.9)

and reduce it using button (C.10).

Contrast (7“ monitor)

Press the button (C.8) on the indoor station twice and the OSD will

display ‘Contrast’. You can now increase the contrast using button (C.9)

and reduce it using button (C.10).

Colour saturation (7“ monitor)

Press the button (C.8) on the indoor station three times and the

OSD will display ‘Colour’. You can now increase the colour saturation

using button (C.9) and reduce it using button (C.10).

Melody selection (3.5“ and 7“ monitor)

The next melody is played every time you press the button

(B/C.11). The last melody to be played is automatically stored.

VISTUS VD-600_I-Manual_210x240_Fin9.indd 17 10.06.13 15:52

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ME VD 603 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info