Bedienungsanleitung Melissa 16590008 (Seite 28 von 44) (Deutsch, Englisch, Dänisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

507952

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Positioning the appliance

• Alwaysplacetheapplianceonadry,level,rmand

heat-resistantsurfacewellawayfromanyedges.

• Thebackoftheappliancemustbesupportedbya

rear wall.

Connection

1. Theappliancemustbeconnectedtoa230-voltAC

current, 50 Hz.

2. Always use new hoses when installing the

appliance. Old hoses should not be reused for new

installations.

3.

The water intake on the appliance ends in a ¾”

female plug – check that the correct hose is

used.

Do not overtighten the connection, as this can

damage the thread.

There should be a stopcock connected to the

hose, so it is easy to disconnect the water supply

to the appliance.

Regulations stipulate that the water tap

 connectionshouldbewithanon-returnvalve.

However, we recommend that the appliance has

 apermanentconnectiontothewatersupply.You

must ensure that the correct spacers or adapters

are used to connect the appliance in a safe and

responsible way.

The appliance can be connected to both hot and

cold water supply.

• Ifthehotwatersupplytemperaturecannot

be maintained under 60 ºC, the appliance

must be connected to the cold water supply,

as it may be damaged by water that is too

hot.

• Whenconnectedtohotwater,washtimes

are reduced by approximately 15 minutes.

There will also be a slight reduction in wash

  efciency.

The appliance is equipped with a water level

gauge, which ensures that the appliance stops

automatically if there is a drop in water pressure.

until the hose is secure.

The drainage hose is fed upwards like an

 upturnedUovertheaccompanyingplastic



 thedrain.Thispreventsdrainagewaterowing

back into the appliance. For increased

 protection,areuxvalve(notincluded)canbe

used.

The drainage hose should be fed down into

a drainage pipe, which must be no higher than

max. 75 cm above the base of the appliance.

The drainage pipe diameter should be at least

4 cm in order to ensure that air can escape

around the drainage hose. Extra drainage hose (if

 any):max.length4m.

5. Turn water on.

NOTE!ASSOONASTHEWATERSUPPLYISTURNED

ON,THEREISPRESSURISEDWATERINTHEHOSE

ANDAPPLIANCE,EVENIFTHEWATERSUPPLYIS

SUBSEQUENTLYTURNEDOFFAGAIN!

Fitting the lter, rack and cutlery basket

• Fittheltersinthebaseoftheappliance.

Fitthemainlter(9)rst.Theninsertthene

 andcoarselterelement(8).Thenturnthelter

clockwise.

Checkthattheltersarecorrectlyttedandthat

the dishwasher arm (7) rotates freely and can

turn a complete circle.

• Therack(1)isequippedwithwheels,sothatit

slides easily in and out.

• Positionthecutlerybasket(2)ontherack.The

cutlery basket can be removed from the rack if it

is not required, e.g. when washing serving dishes,

bowlsandotherlargeobjects.

Filling salt

Water hardness varies from place to place and from

waterworks to waterworks. Hard water can leave

white deposits on dishes and requires more detergent.

This appliance is therefore equipped with a softener,

which softens the water in the appliance with the aid

of salt, which helps to ensure good washing results.

Softwaterrequireslessdetergent,sothesalthelpsto

reduce detergent consumption and also protect the

environment.

To ll with salt:

• Removethecutlerybasketandscrewoffthesalt

compartment cap (6).

• Fitthefunnel(10)intotheport.Fillwithabout1kg

salt.

• Closecap.

• IMPORTANT!Immediatelyafterllingwithsalt,runa

quick wash program to avoid salt water corrosion of

the parts.

• Rellwithsaltwhenthesaltindicator(c)lightsup.

NOTE!ITISIMPORTANTTOADDSALTBEFORETHE

FIRSTWASHCYCLE!ONLYUSESALTINTENDEDFOR

DISHWASHERS.

Filling dishwasher rinse agent

Thesurface-activesubstancesindishwasherrinse

agent reduce surface tension in the water for quicker,

betterdrying.Usingadishwasherrinseagentalso

means dishes are cleaner and glass remains clear and

shiny.

To ll with dishwasher rinse agent:

• Screwthecapoffthedishwasherrinseagent

compartment (3), turning it to the left (in the

directionofthearrow).Liftcapoff.

• Filldishwasherrinseagentbutbecarefulnotto

overllthecompartment.

• Screwthecapbackon,turningittotheright(inthe

direction of the arrow) to close.

• Rellwhenthedishwasherrinseindicator(d)lights

up.

Screwthehosetothewatersupply(

)atthewater

intake (

Attach the drainage hose ( ) to the drainage nozzle

( ) using the hose clip (

). Tighten the hose clip

U-bend( )beforebeingfeddownwardsinto

Melissa 16590008 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info