Bedienungsanleitung Mercedes AMG GT Roadster 2018 (Seite 233 von 294) (Englisch)

703629

233

Zoom out

Zoom in

Vorherige Seite

1/294

Nächste Seite

Garage door remote control A is not included

with the integrated garage door opener.

Select SmartKey position 2 with the Start/

Stop button (

Y page 111).

Select one of buttons ; to ? to use to con-

trol the garage door drive.

To start programming mode: press and

hold one of buttons ; to ? on the integrated

garage door opener.

The garage door opener is now in program-

ming mode. After a short time, indicator

lamp : lights up yellow.

Indicator lamp : lights up yellow as soon as

button ;, = or ? is stored for the first time.

If the selected button has already been pro-

gramed, indicator lamp : will only light up

yellow after ten seconds have elapsed.

Release button ;, = or ?. Indicator

lamp : flashes yellow.

To program the remote control: point

garage door remote control A towards but-

tons ; to ? on the rear-view mirror at a dis-

tance of 2 to 8 in (5 to 20 cm).

Press and hold button B on remote control

A until indicator lamp : lights up green.

When indicator lamp : lights up green: pro-

gramming is finished.

When indicator lamp : flashes green: pro-

gramming was successful. The next step is to

synchronize the rolling code (

Y page 231).

Release button B on remote control A for

the garage door drive system.

If indicator lam

p : lights up red: repeat the

programing procedure for the corresponding

button on the rear-view mirror. When doing

so, vary the distance between remote control

A and the rear-view mirror.

The required distance between remote con-

trol A and the integrated garage door opener

depends on the garage door drive system.

Several attempts might be necessary. You

should test every position for at least

25 seconds before trying another position.

Synchronizing the rolling code

Pay attention to the "Important safety notes"

(

Y page 230).

If the garage door system uses a rolling code,

you will also have to synchronize the garage

door system with the integrated garage door

opener in the rear-view mirror. To do this you will

need to use the programming button on the door

drive control panel. The programming button

may be located in different places depending on

the manufacturer. It is usually located on the

door drive unit on the garage ceiling.

Familiarize yourself with the garage door drive

operating instructions, e.g. under "Program-

ming additional remote controls", before carry-

ing out the following steps.

Your vehicle must be within reach of the garage

door or gate opener drive. Make sure that nei-

ther your vehicle nor any persons/objects are

present within

the sweep of t

he door or gate.

Select SmartKey position 2 with the Start/

Stop button (

Y page 111).

Get out of the vehicle.

Press the programming button on the door

drive unit.

You now have 30 seconds to initiate the next

step.

Get into the vehicle.

Press previously programed button ;, =

or ? on the integrated garage door opener

repeatedly until the door closes.

The rolling code synchronization is then com-

plete.

Notes on programming the remote con-

trol

Canadian radio frequency laws require a "break"

(or interruption) of the transmission signals

after broadcasting for a few seconds. Therefore,

these signals may not last long enough for the

integrated garage door opener. The signal is not

recognized during programming. Comparable

with Canadian law, some U.S. garage door open-

ers also feature a "break".

Proceed as follows:

if you live in Canada.

if you have difficulties programming the

garage door opener (regardless of where you

live) when following the programming steps.

Press and hold one of buttons ; to ? on the

integrated garage door opener.

After a short time, indicator lamp : lights up

yellow.

Release the button.

Indicator lamp : flashes yellow.

Press button B of garage door remote con-

trol A for two seconds, then release it for two

sec

onds.

Press button B again for two seconds.

Features

231

Stowage and features

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mercedes AMG GT Roadster 2018 Seite 233

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mercedes AMG GT Roadster 2018

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info