Bedienungsanleitung Mercedes S-Class Coupe - 2015 (Seite 315 von 402) (Englisch)

624701

315

Zoom out

Zoom in

Vorherige Seite

1/402

Nächste Seite

gramming of additional remote controls",

before carrying out the following steps.

Your vehicle must be within reach of the

garage door or gate opener drive. Make sure

that neither your vehicle nor any persons/

objects are present within the sweep of the

door or gate.

Turn the SmartKey to position 2 in the igni-

tion lock (Y page 147).

Get out of the vehicle.

Press the programming button on the door

drive unit.

Usually, you now have 30 seconds to ini-

tiate the next step.

Get into the vehicle.

Press previously programmed button ;,

= or ? on the integrated garage door

opener until the door closes.

The rolling code synchronization is then

complete.

Notes on programming the remote con-

trol

Canadian radio frequency laws require a

"break" (or interruption) of the transmission

signals after broadcasting for a few seconds.

Therefore, these signals may not last long

enough for the integrated garage door

opener. The signal is not recognized during

programming. Comparable with Canadian

law, some U.S. garage door openers also fea-

ture a "break".

Proceed as follows:

if you live in Canada

if you have difficulties programming the

garage door opener (regardless of where

you live) when using the programming

steps

Press and hold one of buttons ; to ? on

the integrated garage door opener.

After a short time, indicator lamp : lights

up yellow.

Release the button.

Indicator lamp : flashes yellow.

Press button B of garage door remote

control A for two seconds, then release it

for two seconds.

Press button B again for two seconds.

Repeat this sequence on button B of

remote control A until indicator lamp :

lights up green.

When indicator lamp : lights up green:

programming is finished.

When indicator lamp : flashes green: pro-

gramming was successful. The next step is

to synchronize the rolling code.

Release button B of remote control A of

the garage door drive.

If indicator lamp : lights up red: repeat the

programming process for the correspond-

ing button on the rear-view mirror. When

doing so, vary the distance between remote

control A and the rear-view mirror.

The required distance between remote

control A and the integrated garage door

opener depends on the garage door drive

system. Several attempts might be neces-

sary. You should test every position for at

least 25 seconds before trying another

position.

Problems when programming

If you are experiencing problems programing

the integrated garage door opener on the

rear-view mirror, take note of the following

instructions:

Check the transmitter frequency used by

garage door drive remote control A and

whether it is supported. The transmitter

frequency can usually be found on the back

of the garage door drive remote control.

The integrated garage door opener is com-

patible with devices that have units which

operate in the frequency range of 280 to

433 MHz.

Replace the batteries in garage door

remote control A. This increases the like-

lihood that garage door remote control A

will transmit a strong and precise signal to

the integrated garage door opener.

Features

313

Stowage and features

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mercedes S-Class Coupe - 2015 Seite 315

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info