657614
52
Zoom out
Zoom in
Vorherige Seite
1/129
Nächste Seite
52
a
b
c
d
Synchronizing and readjusting
Hydraulic rim brakes are synchronized together with the
alignment of the brake pads. The position of the brake
lever where the brake starts to act, also referred to as the
pressure point, can be adjusted to the size of the hand
as well as to individual convenience at the same time.
Also observe in this regard the instructions given in the
chapter “Adjusting the brake lever reach“.
As the brake pads wear down, the pressure point moves
towards the handlebar grips. Make absolutely sure you
cannot pull the brake lever all the way to the handle-
bar grip. Most brake models are, however, fitted with a
bolt or a small knob at the brake lever unit to compen-
sate the wear. Observe the operating instructions of the
brake manufacturer on this MERIDA CD-ROM. If you
are in doubt or if you have any questions, contact your
MERIDA dealer.
I
Read the instructions of the brake manufac-
turer on this MERIDA CD-ROM carefully be-
fore removing the wheel or doing any main-
tenance work. Improper operation can lead to brake
failure.
Disc brakes
Functioning and wear
The most striking feature of disc brakes
(a-c)
is their out-
standing braking effect. They respond a lot faster in wet
conditions than rim brakes do and achieve their normal
high braking power within a very short time. They re-
quire little maintenance and do not wear down the rims
as rim brakes do. Disc brakes consist of the brake cal-
iper, the rotor, the brake lines or cables as well as the
brake lever unit
(d)
. Actuating the brake lever compress-
es the hydraulic pistons through hydraulic pressure or
mechanically, pushing the brake pads against the rotor.
The friction generated by braking causes wear to the
brake pads as well as to the rotors. Frequent rides in the
rain and dirt and over hilly terrain can accelerate wear
on both braking surfaces. Depending on the manufac-
turer and the model there are different ways of checking
the brake pads and rotors for their wear limits.
G
New brake pads have to be broken in until
they reach their optimal braking power. Ac-
celerate your MERIDA bike about 30 to 50
times to around 30 kmh and bring it to a halt each time.
This procedure is finished, when the force required at
the lever for braking has stopped decreasing.
G
Disc brakes get hot in use. For this reason do
not touch the rotors directly after stopping,
especially after a long downhill ride.
52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Merida Pedelec wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info