Bedienungsanleitung Meridian DVP 1080 HD (Seite 18 von 34) (Englisch)

494961

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

O p e r a t i n g t h e

d i g i t a l v i d e o

p r o c e s s o r

1 4

To adjust the tint

TINT 50

|•••••• |

Tint is only available with composite or S-Video sources.

If the image colour still seems off balance with the tint set correctly the greyscale of the

display may need adjusting. Contact your installer for assistance.

Suggested test pattern: REVERSE COLOR BAR.

To adjust the detail

DETAIL 10

|• |

This enhances the detail in the image.

Too much enhancement will produce unnatural looking edges and ringing. The higher

quality the source, typically the less enhancement required. With poor digital sources, such

as a poorly transferred DVD or a very compressed satellite channel, reducing the detail level

can help to make compression artifacts less visible.

Suggested test pattern: DVD Movie with a close up of a face in a still frame. Adjust so the

face has detail but the edges do not look fake (such as along the bridge of the nose.

To set advanced colour

• Select the ADVANCED COLOUR SYS option on the PICTURE menu:

ADVANCED COLOR SYS

NORMAL

• Press > or < to toggle the setting between NORMAL and BYPASS.

Advanced colour mode activates colour edge enhancement and cross-colour suppression to

improve the image and remove certain video artifacts. This should be set to

NORMAL for

most sources.

With a few movies that contain large amounts of colour, such as animation, these

enhancements may cause colour flickering. Set the mode to

BYPASS if this occurs.

Adjusting the aspect ratio

The aspect ratio options allow you to select the proper aspect ratio of the source being

viewed.

Note that the correct screen shape must be set in the

SETUP menu during initial

installation for the settings to function properly; see

Configuring the digital video processor

page 17.

The following aspect ratios are available: anamorphic, 4:3, or letterbox.

To select anamorphic aspect ratio

• Press Anamorphic on the remote control.

This selects the correct aspect ratio for sources formatted for widescreen displays,

sometimes called Enhanced for Widescreen.

DVD players must be set for 16:9 displays for proper screen shape, see the DVD player’s

Setup menu.

For Meridian DVD players select

16:9 Widescreen in the Display Aspect Ratio menu.

To select letterbox aspect ratio

• Press Letterbox on the remote control.

This selects the proper aspect ratio for sources formatted for the letterbox screen format.

This mode can also be used with anamorphic 2.35:1 (cinema scope) sources when

combined with an anamorphic lens on a 16:9 projector. The benefit is that the full

resolution of the 16:9 display chip is used to create the active video, improving resolution

and light output. The trigger output can be programmed to control the motorised lens

attachment.

To select the 4:3 aspect ratio

• Press 4:3 on the remote control.

This selects the correct aspect ratio for sources formatted for a 4:3 screen format.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Meridian DVP 1080 HD Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info