Bedienungsanleitung Meridian DVP 1080 HD (Seite 27 von 34) (Englisch)

494961

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

Tr o u b l e s h o o t i n g

2 3

When SET: ACTIVE OUTPUT / DVI is selected within the SETUP MENU, the ANALOG

OUTPUTS are disabled; however, will pass analogue to analogue signals (select appropriate

input on the display).

There is Dark Banding/Streaking while the video image is

changing; how do I fix this?

The video image is either positioned (Phased) too far to the left/right, or the image is too

wide. Though the image may be “filling” the viewable screen area, the display is having

difficulty finding the actual Clamp Pulse (sync signal). The display is now “Clamping” to the

Peak Whites of the video signal; or rather, “clamping” to video, not the sync pulse.

You should recalibrate the display device utilizing a master video test pattern. Utilize a

Component (YCrCb) DVD source and a Safe-Area test pattern (AVIA or DVD Essentials

calibration DVD).

Digital Display Device (Plasma, D-ILA, DLP or LCD)

• Utilize a “Screen Area” test pattern from a calibration test DVD

• Reduce the video image size until you see the Active Picture area of both the left side

and right side of the video image

• Center the image on the screen using the positioning controls of the display device only

• Digital displays will have sizing controls labeled Pixel Clock, Dot Clock or just Clock, etc.

This adjustment will expand/contract the image to from the Right; the Left side of the

image should remain relatively fixed to its position

• Use Horizontal Size, Positioning controls and Clock adjustment to center/position the

image on screen.

You will need to utilize all controls to achieve/massage image centering.

• Once the image is centered correctly, fully expand the image to the edge of the screen.

Analogue CRT Display Device

• Use a “Screen Area” setup pattern from a calibration test DVD.

• Reduce the image size by 10% to 15%.

• Un-blank Left, Right, Top and Bottom Blanking.

• Increase BRIGHTNESS to 75%.

• Image should be clearly seen within the raster area.

• Phase picture to center image within the raster area.

• Center raster (with image) on the screen.

• Blank Left, Right, Top and Bottom Blanking to edge of image.

• Increase Left/Right and Top/Bottom Size to the edge of screen.

My picture is Magenta or Pinkish in color

RGBHV out into YPrPb in = MAGENTA picture.

The default analogue ACTIVE OUTPUT of the DVP1080 is 5-wire RGB (RGBHV). If your only

video input option to the display is via YPrPb, you must first change the ACTIVE OUTPUT on

the DVP-1080 from RGB to YPrPb within the SETUP MENU.

Note: The DVI OUTPUT is disabled once YPrPb has been selected; YPrPb is not a valid

output format within the DVI domain.

• Enter the SETUP MENU by pressing

Menu on the IR remote for seven seconds

• Press

A until the upper LCD display reads either of the following:

SET: OUTPUT FORMAT / ANALOG RGB + DVI

SET: OUTPUT FORMAT / ANALOG RGB

• Press < or > to select SET: OUTPUT FORMAT / ANALOG YPrPb

• Press

Menu to return to the USER MENU

Note: ONLY select either 1920x540p or 1280x720p scanrates if the display device does

not have an available 5-wire RGBHV or D-15 VGA input connection.

• If you are connecting the DVP-1080 and display device via RGBHV, and your picture

is MAGENTA, you will then need to change the displays input format from COMP

(Component) to RGB or PC.

• Verify that the output/input cable(s) have not been swapped.

• Verify continuity of cable terminations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Meridian DVP 1080 HD Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info