Bedienungsanleitung Meridian DVP 1080 HD (Seite 25 von 34) (Englisch)

494961

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

Tr o u b l e s h o o t i n g

2 1

Connecting the processor to the display

Which output scan rate should I choose for my display?

The appropriate output scan rate selection is usually determined by the actual native pixel

density of a digital display device, or the physical CRT size of an analogue display device

(7”, 8” or 9” CRT).

Each display device will specify their individual video/computer input capabilities. All display

devices will list their specific video/computer input specifications within the User’s Manual,

and are typically located within a “Table of Supported Resolutions”, or under similar

nomenclature.

The following represent basic examples for possible output scan rate selections:

Display Type Display resolution DVP1080 scan rate

Plasma TV

1366 x 768 1366 x 768

Digital projector

1366 x 768 1280 x 720

CRT projector 7" CRT

8" CRT

9" CRT

1920 x 540 or 1280 x 720

1280 x 720 or 1440 x 960

1440 x 960 or 1920 x 1080

CRT rear screen 480 i/p, 1080i, or 720p 1920 x 540p or 1280 x 720p

Note: Occasionally, a digital display device may not actually accept the signal received

from the processor at its native pixel resolution. Choose a standard DTV signal in this

instance, such as 1280x720 (default setting), or 1920x540 (1080i equivalent).

There are sparkles appearing throughout the image when using

the DVI output

Cable length is too long to support the output resolution selected on the processor

• Sparkles may occur if the resolution selected on the DVP-1080 processor has exceeded

the ability of the DVI cable to transmit all of the video data (missing bits = sparkles).

This is directly dependent upon cable quality (contact cable manufacturer regarding

length to resolution specifications).

• Unassisted DVI cable lengths to 50ft (15.24m) have been achieved with resolutions of

1024p and lower.

• Cable lengths of 50ft (15.24m), or greater, may require a DVI to Fibre Optic cable

connection between the processor and display for resolutions higher than 1024p;

consult Cable Manufacturer

You can also use a Meridian HDMAX 121 extender/booster at the display end to solve

problems like this. Contact your Meridian authorised dealer for details.

Can the DVP1080 output both an analogue and a digital signal

simultaneously?

Yes. Four potential SET: ACTIVE OUTPUT modes are available through the DVP-1080

SETUP MENU:

Mode Description

ANALOG RGB + DVI Both DVI OUTPUT and ANALOG OUTPUTS are active (Default

Setting)

ANALOG RGB Only ANALOG OUTPUTS are active (RGBHV and MONITOR)

DVI Only DVI OUTPUT is active (RGBHV and MONITOR out disabled)

ANALOG YPrPb Only ANALOG OUTPUTS are active (DVI output disabled)

This chapter provides suggested solutions to common problems that may occur when installing and using

the DVP1080HD.

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Meridian DVP 1080 HD Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info