Bedienungsanleitung Mesko MS 7911 (Seite 6 von 124) (Alle Sprachen)

732304

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Delay start function:

The remote controller transmits signals to the system.

Button "B" - press it to select operation mode: cool mode → dry mode → fan mode.

Button "A" - the appliance will be started when it is energized or will be stopped when it is in operation, if you press this button.

Button "C" / "D" - press to adjust the room temperature and the timer.

Button "E" - press to set or cancel sleep mode.

- In the cooling mode, press both buttons “F” and “D” to turn on the sleep mode, then the unit will work on Energy - Saving and quiet type.

The sleep model control lamp “N” will switch on the control panel.

Button "F" - press it to select fan speed in sequence: low / high wind speed.

Button "G" - press to set the operation time from 1 to 24 hours.

Switch off the device and then press the button “G”, next press up button “D” or down button “C” to select the required time value. The

maximum power on delay time is 24 hours. The device will be switched on after the delay time has elapsed.

Switch on the device and then press the button “G” , next press up button “D” or down button “C” to select the required time value. The

maximum power off delay time is 24 hours. The device will be switched off after the delay time has elapsed.

- Power ON delay setting:

Press button “E” to select the Sleep Mode:

Press button “G” to select operation period, when the LCD screen flashes, press up button “D” or down button “C” to select the required

time range. Time setting range 1-24 hour and can be adjusted up or down by one hour.

- Power OFF delay setting:

Flashing will stop soon and LED screen come back to show required temperature.

REMOTE CONTROLLER operation – picture E

To increase the service life of the compressor, it has a 3-minute delay booting protection function after the compressor is turned off.

When water in the water pan exceeds the warning level, the machine will automatically sound an alarm, and the "FULL" indicator light “M”

will flash. At this time, drain the water according to drainage instructions. After the water is emptied, the machine will automatically return to

the original state.

3. Protection Function of the Compressor

In cooling, dehumidifying or economic power saving mode, if the temperature of the exhaust pipe is too low, the machine will automatically

enter protection status; if the temperature of the exhaust pipe rises to a certain temperature, it can automatically revert to normal operation.

PROTECTION DEVICES

2. Overflow Protection Function “M”:

1. Frost Protection Function:

- In cooling and fan mode, press the button “F” to select high or low wind speed operation. In too cold conditions, it may not run according to the

set wind speed.

- In dehumidifying mode, pressing the button “F” is invalid, and the fan will forcibly choose low wind speed operation.

Remote controller – Picture E

C. Timer / Temperature down button D. Timer / Temperature up button

G. Timer button

E. Sleep model F. Fan speed button

CONTROL PANEL operation – picture D

A. Power button B. Mode button

Press button “B” to switch mode, between cooling mode → fan mode → dehumidifying mode.

Press button “A” to turn on and turn off the machine, the buzzer will play signal once. The control lamp “O” will switch on the control panel.

Press button “D/C” Up / Down to change the setting temperature or setting time, operate as follows:

- While setting temperature, press button up or down button to select the required temperature (not available in fan or dehumidifying

mode).

- While setting time, press up button or down button to select the required time.

Press button „F” to select the Fan speed:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mesko MS 7911 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info