Bedienungsanleitung Mesko MS 7911 (Seite 7 von 124) (Alle Sprachen)

732304

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

2. Continuous drainage - option applicable to dehumidifying mode ONLY - shown on picture F2.

Unscrew the drainage cover, and unplug the water plug. Set the drainage pipe (not included in kit) into the water outlet. Connect the drainage

pipe to the bucket.

This machine has two drainage methods: manual drainage and continuous drainage.

1. Manual drainage – picture F1.

CLEANING & MAINTENANCE

Cleaning: before cleaning and maintenance, turn off the machine and unplug the plug.

a) Housing cleaning

Clean with surface of device with a wet soft cloth. Don't use chemicals, such as benzene, alcohol, gasoline, otherwise, the surface of the

device will be damaged or even the whole machine will be damaged.

If the filter screen is clogged with dust, and the effectiveness of the device is reduced, be sure to clean the filter screen once every two

weeks.

DRAINAGE INSTRUCTIONS:

b) EVA filter cleaning

- Clean the upper filter screen frame – picture G.

- Loosen one screw in the back cover and remove the EVA filter mesh (5).

- Put the filter into warm water with neutral detergent (about 40℃ / 104℉) and dry it in the shade after rinsing clean.

When the device stops after the water is full, you see on control panel the “M” control lamp is flashing. Turn off the device power and

unplug the power plug. Move the machine carefully, so as not to spill the water in the water pan at the bottom of the body. Place the water

container below the water outlet behind the housing. Unscrew the down cooler drain hole (8) and unplug the water plug, the water will

automatically flow into the water container. Keep the drainage cover and the water plug properly. During drainage, the body can be tilted

slightly backwards. If the water container cannot hold all the water, before the water container is full, stuff the water outlet with the water

plug as soon as possible to prevent water from flowing to the floor or the carpet. When the water is discharged, stuff the water plug, and

tighten the drainage cover.

Reason 3: The ambient temperature is too low or too high. So, recommend to use the device in at the temperature of 7-35 ℃ (44-95 ℉).

1. Unscrew the drainage cover, unplug the water plug, and discharge the water in the water pan into other water

Reason 1: The distance between the machine and the remote control is too far. So, let the remote control get close to the device, and make

sure that the remote control directly faces to signal receptor (I) at control panel.

2. Turn on the device, adjust it to low speed fan mode, and maintain this state until the drainage pipe (not included in kit) becomes dry, so as to

keep the inside of the housing in a dry state and prevent it from mildewing.

6. Remove batteries of the remote control and keep them properly.

STORAGE

4. Remove the air exhaust pipe elements.

Reason 1: There is direct sunlight. So, pull the curtain.

Reason 3: The EVA filter is dirty. So, clean it.

Problem I.: The air conditioning does not work.

Reason 5: In dry mode, the ambient temperature is too low. So, the device should be placed in a room with an ambient temperature of

greater than 17 ℃ (62 ℉).

Problem III.: Big Noise

Reason: The device is not placed on a flat surface. So, put the device on a flat and hard place to reduce noise.

5. Cover the air conditioning with a plastic bag. Put the air conditioning in a dry place, keep it out of the reach of children, and take dust control

measures.

TROUBLESHOOTING

Reason 1 :There is no electricity. So, turn it on after connecting it to a socket with electricity.

3. Turn off the device, remove the plug from the socket, install the plug and drain cover.

containers or directly tilt the housing to discharge the water into other containers.

Reason 4: In cooling mode, the room temperature is lower than the set temperature. So, change the set temperature.

Problem II.: The cooling effect is not good.

Reason 2: Doors or windows are open; there are a lot of people; or in cooling mode, there are other sources of heat. So, close doors and

windows, and add new air conditioner.

Reason 4: The air inlet or outlet is blocked. So, clear obstructions.

Do not repair the device yourself. Qualified repair will void the warranty.

Reason 2: The overflow indicator displays "FL". So, discharge the water.

Problem IV.: Compressor does not work.

Reason: Overheat protection starts. So, wait for 3 minutes until the temperature is lowered, and then restart the machine.

Problem V.: The remote control does not work.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mesko MS 7911 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info