451401
19
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
19
ENGLISH
7.6 Dust collector connec-
tion
A
Danger!
Some types of saw dust (e.g. of
oak, beech and ash wood) can cause
cancer when inhaled: always use a
dust collector when working indoors
(required air speed at the saw's suc-
tion connector 20 m/s).
A
Caution!
Operation without a dust col-
lector is only possible:
outdoors;
for short-term operation
(up to max. 30 minutes);
with dust respirator.
If no dust collector is used chips
will accumulate, which need to be
removed periodically.
Connect dust collector or industrial vac-
uum with a suitable adaptor to the dust
extraction port.
7.7 Mains connection
B
Danger! High voltage
Operate saw in dry environment
only.
Operate saw only on a power
source matching the following
requirements (see also “Techni-
cal Specifications”):
mains voltage and system fre-
quency conform to the voltage
and frequency shown on the
machine's name plate;
fuse protection by a residual
current operated device (RCD)
of 30 mA sensitivity;
outlets properly installed,
earthed and tested.
Three-phase outlets with neu-
tral wire.
3
Note:
Check with your local Electricity
Board or electrician if in doubt whether
your house service connection meets
these requirements.
Position power supply cable so it
does not interfere with the work
and is not damaged.
Protect power supply cable from
heat, aggressive liquids and
sharp edges.
Use only rubber-jacketed exten-
sion cables with sufficient lead
cross-section (3 x 1.5 mm
2
).
Do not pull on power supply
cable to unplug.
A
Changing the direction of rota-
tion (machines with three-phase
motor only):
Depending on the phase sequence of
the electric supply it is possible the
saw blade will turn in the wrong direc-
tion. This can lead to the workpiece
being hurled away when attempting
to make a cut. The direction of rota-
tion must therefore be checked every
time the saw is connected to another
outlet.
In case of an incorrect direction of
rotation, the wiring of the outlet must
be changed by a qualified electrician:
1. After the saw and all of its safety
devices have been assembled, con-
nect it to the mains supply.
2. Start saw and switch OFF immedi-
ately.
3. Observe the correct rotational direc-
tion of the band saw blade: In the
cutting area the band saw blade
must run downwards.
4. If the saw blade runs in the wrong
direction, unplug the power cable at
the saw's connector.
5. Have the electric supply changed by
a qualified electrician!
A
Danger!
To reduce the risk of personal
injury as much as possible, the fol-
lowing safety recommendations
should be observed when operating
the saw.
Use personal protection gear:
dust respirator;
hearing protection;
safety goggles.
Cut only one workpiece at a time.
Always hold the workpiece down
on the table.
Do not jam the workpiece.
Do not attempt to stop the band
saw blade by pushing the work-
piece against its side.
If the type of work requires, use
the following:
push stick – if distance rip
fence – band saw blade less
than 120 mm;
work support – for long stock,
which would otherwise fall off
the table on completion of the
cut;
dust collector;
an appropriate jig when cutting
round stock, to keep it from
turning;
a suitable guide for firm sup-
port when cutting thin stock
layed on edge.
Before starting work, check to
see that the following are in
proper working order:
band saw blade;
upper and lower blade guard.
Replace damaged parts immedi-
ately!
Assume correct work position
(the band saw blade's teeth must
point towards the operator).
Never cut several workpieces at
the same time – and also no bun-
dles containing several individual
pieces. Risk of personal injury if
individual pieces are caught by
the saw blade uncontrolled.
c
Drawing-in/trapping hazard!
Do not wear loose clothing, jewel-
lery, or gloves, which may get
caught and wound up by revolv-
ing machine parts.
Contain long hair with a hairnet.
Never cut stock to which ropes,
cords, strings, cables and wires
are attached or which contain
such materials.
8.1 Upper blade guide
adjustment
The height of the upper blade guide (53)
needs to be adjusted:
51 52
8. Operation
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo BAS 505G wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info