451401
17
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
17
ENGLISH
Lower blade guard
The lower blade guard (33) protects
against inadvertent contact with the
band saw blade below the saw table.
Housing door
The housing door (34) protects against
contact with the rotating parts inside the
machine.
The housing door is fitted with a safety
interlock. This turns the motor OFF when
the housing door is opened while the
saw is running.
During operation the housing door must
be closed.
Push stick
The push stick serves as an extension of
the hand and protects against accidental
contact with the saw blade.
The push stick must always be used if
the distance between band saw blade
and a rip fence is less than 120 mm.
Guide the push stick at an angle of 20°
… 30° against the band saw table's sur-
face.
When the push stick is not used, it can
be stored on the push stick holder pro-
vided at the band saw frame.
Replace push stick if damaged.
Cast grey iron table.
Upper blade guide with 3 bearings.
Up-to-date technology, designed for
lasting durability and accuracy.
Set upper blade guide to its lowest
position.
Remove projecting accessories.
When shipping, use original packing
if possible.
3
Note:
In this chapter the essential oper-
ating elements of the machine are intro-
duced.
The proper use of the saw is detailed in
chapter “Operation”. Read this chapter
before using the saw for the first time.
ON/OFF switch
To start = press green switch button
(35).
To stop = press red switch button
(36).
In the event of a power failure an under-
voltage relay will trip. This prevents the
machine from starting up when the
power is restored. To restart, the green
switch button must be pressed.
Setting knob for band saw blade ten-
sion
With the setting knob (37) the band saw
blade tension is corrected, if necessary:
Turning setting knob in direction
indicated by arrow increases the
blade tension.
Turning setting knob in the opposite
direction reduces the blade tension.
Setting knob for blade tracking
adjustment
With the setting knob (38) the tilt of the
upper band saw wheel can be adjusted,
if necessary. This tracking adjustment is
required to have the blade run at the
front edge of the band saw wheels:
Turning clockwise = blade moves to
the rear.
Turning counter-clockwise = blade
moves to the front.
Saw table tilt
After loosening the locking screw (39)
the saw table (40) tilts steplessly through
20° against the blade.
Rip fence
The rip fence (41) is clamped to the
front. It can be used on both sides of the
blade.
A
Danger!
Start the saw only after the fol-
lowing preparations are completed:
saw is mounted;
saw table is installed and aligned;
4. Special Product Features
32
33
34
5. Transporting the Saw
6. Machine Details
35
36
37
7. Initial Operation
38
39
40
41
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Metabo BAS 505G wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info